Q/1/ Single phase half-wave uncontrolled rectifier. The battery charger circuit that is used to charge a battery of electric vehicle from the main supply voltage of 250 V,50 Hz through a limiting resistor R = 102, a=40°. Calculate i) The voltage that used to charge an electric vehicle ii)what are power diodes types

Q/1/ Single phase half-wave uncontrolled rectifier. The battery charger circuit that is used to charge a battery of electric vehicle from the main supply voltage of 250 V,50 Hz through a limiting resistor R = 102, a=40°. Calculate i) The voltage that used to charge an electric vehicle ii)what are power diodes types

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

How is a solid-state diode tested? Explain.
What is CEMF?
In a full wave rectifier circuit involving double diodes, a sinusoidal input signal of the following nature is applied e=10 sin(500*pi*t) V. What will be value of the dc voltage obtained at the output of the rectifier.
0:- Consider the circuit in Figure a) What type of circuit is this? b) Find and Sketch the voltage waveform across RL, assume the diodes are practical. c) If 100uf capacitor parallel with the resistor, calculate the ripple is connected factor I O o D
Consider the circuit shown in Figure 2. The cut-in voltage of each diode is . Let and assume both diodes are conducting. Determine if this is a valid assumption and explain your answer. And calculate the values of IR, ID, Ip2, and V.. Rj =1.7 kQ ww VB =1 V D1 Dz R2D 4 kQ Figure 2
Draw the input waveform and output waveform for the circuit given below with proper values marked in the figure. Assume D1 as germanium and D2 as silicon diodes. Input Vpp%3D20V, V1=3 V and V2=10 V. R D2 D1 Vin Vout V1 V2 Maximum voltage of output waveform Minimum voltage of output waveform Ps
Q3/a/ what is the function of the inductance (L) in a single phase half wave thyristor ? b/ For 3 phase half wave rectifier source voltage is 100 sinwt with a = 40° find the Vav and draw the output voltage?
Draw the input waveform and output waveform for the circuit given below with proper values marked in the figure. Assume D1 as silicon and D2 as germanium diodes. Input Vpp=20V. V1=5 V and V2=9 V. R www D1 Vin Vout v1 V2 Maximum voltage of output waveform Minimum voltage of output waveform
Figure 2 shows a circuit for charging a 12 v battery. If Vs is a sinusoidal input with 30 v peak amplitude, determine: i. The fraction of each cycle during which the diode conducts. ii. The peak value of the diode current iii. The maximum reverse bias voltage that appears across the di ode. 100 n 12 V Figure 2
Calculate the current flowing through the given circuit and the voltage value at the V0 ends. (Threshold voltage = 0.3V for Germanium diodes, Threshold voltage for silicon diodes = 0.6V)
3 Given the bridge-type full-wave rectifier circuit shown 220V 60Hz 220V:Es Es D1 D2 D3 D4 The load resistor is 220 and the transformer average current is 300mA. Determine: (a) Average value, RMS value, and frequency of load voltage VRL. (b) Average current and PIV of each diode. RL
H.W4 The diode in the single-phase half wave rectifier has a reverse recovery time of t 150μsec and the source voltage V₁ 200V at frequency = 5 kHz. Calculate the average output voltage. = =