1. A compound-wound generator terminal connection box contains terminal leads a. F1, F2 and A1, A2. b. S1, S2 and F1, F2. c. S1, S2 and A1, A2. d. S1, S2, F1, F2, and A1, A2. 2. The series winding must be large enough to carry a. the total magnetic flux. b. a 300% overload. c. full line current. d. full line voltage. 3. Select the type of generator that may be used for loads quite distant from the generator. a. overcompounded b. flat compounded c. undercompounded d. differential compounded 4. The normal voltage of a compound generator is changed by adjusting the a. series field shunt. b. brush setting. c. shunt field rheostat. d. equalizer.

1. A compound-wound generator terminal connection box contains terminal leads a. F1, F2 and A1, A2. b. S1, S2 and F1, F2. c. S1, S2 and A1, A2. d. S1, S2, F1, F2, and A1, A2. 2. The series winding must be large enough to carry a. the total magnetic flux. b. a 300% overload. c. full line current. d. full line voltage. 3. Select the type of generator that may be used for loads quite distant from the generator. a. overcompounded b. flat compounded c. undercompounded d. differential compounded 4. The normal voltage of a compound generator is changed by adjusting the a. series field shunt. b. brush setting. c. shunt field rheostat. d. equalizer.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.16MCQ: In developing per-unit circuits of systems such as the one shown in Figure 3.10. when moving across...

See similar textbooks

Similar questions

The solution is largely correct but for a few errors.. Also note that the generator is represented by a voltage source and an impedance in series. Likewise the motor.please taking into consideration the following comment can you please resolve the question
(8) Q2. Correct the wrong sentence if you find it in only (all) of the following sentences: ual and same direct 1) T1 Porto at e Tated current med on low vo "aly mmf:. the. ideal trout -side. copper loss is not a vy ne vau and 10au. 12) Shunt field winding have a large number of turns compared with a series field winding. 13) The voltage regulation of generator A is 10% and that of generator B is 5%. The A is better than generator B. generator poTOTIS Us. 10 Un 14) The external characteristic of a dc generator is affected by armature reaction. 15) The commutating poles or interpoles is connected in parallel with the armature. 16) The de motor should be started by impressing its rated voltage across the armature terminals. at 17) The cumulative compound motor has the advantage of over a series Motor. 18) The torque in a differential compound motor increase and its speed is decreased with an increase in the armature current. 19) The flux in a machine does not vary with time. 20) After…
A generator rated 100MVA, 20KV has X"=X2- 20% and X0-5%. Its neutral is grounded through a reactor of 0.32 ohms. The generator is operating at rated voltage without load and is disconnected from the system when a fault occurs at its terminals. Find the subtransient current in the generator and the line-to-line voltages for subtransient conditions when a) single line-to-ground; b) line-to- line fault occurs at the generator terminals with the generator operating unloaded at rated voltage.
b) Two synchronous generators, G2 and G2, are connected parallelly supplying a load. Generator G1 has a no-load frequency of 50.5 Hz and a slope of 300 MW/Hz. Generator G2 has a no-load frequency of 50.2 Hz and a slope of 500 MW/Hz. The load consumes 250 MW real power. (1) At what frequency does this system operate, and how much power is supplied by each of the two generators? (ii) An additional 100 MW load is added to this power system. What is the new system frequency, and how much power do G1 and G2 supply? (iii) The governor set point of G2 is changed to control system frequency back to 50 Hz. Determine the G2 governor set point.
Q2\ Two generators G1 & G2 are rated 15 MVA, 11 kV and 10 MVA, 11 kV respectively. The generators are connected to a transformer as shown in the following figure. Find the sub- transient current in each generator when a three-phase fault occurs on the high voltage side of the transformer. A/Y 15 MVA, 11 kV, X"gl=j0.10 pu G2 15 MVA, 11/66 kV, Xr-j0.06 pu 10 MVA, 11 kV, X"g2-j0.10 pu
In developing per-unit circuits of systems such as the one shown in Figure 3.10. when moving across a transformer, the voltage base is changed in proportion to the transformer voltage ratings. (a) True (b) False
Some power devices have bidirectional current capability Select one: O a. True b. False The voltage regulation of the transformer will depend on the load Select one: O a. For mainly inductive or resistive load, the voltage regulation is negative O b. For mainly capacitive, inductive or resistive load, the regulation is positive Oc. For mainly capacitive load, voltage regulation is positive and other loads it is negative. O d. For mainly capacitive load, voltage regulation is negative.
E-06, PC-05. Why are the iron cores of most induction coils laminated? To increase the core permeability. To reduce the core reluctance. To reduce the effects of eddy currents. Click Save and Submit to save and submit. Click Save All Answers to save all answers. MacBook Air 吕0 F2 F3 F4 F5 $4 & 4 5 O 6 7 7 W .. E R .... S » D S F G # 3
In the field circuit model of a DC machine, a variable _____ is usually inserted in series with the field winding to vary/control the _____ that flows through that circuit. A resistor, voltage B resistor, current C inductor, current D inductor, voltage
e = 0 Q1: What does happen if we change two currents? a. Q2: What does happen if we have a three-phase four poles machine? Q3: What does happen if we have a two-phase two poles machine? e = 0 Q4: What does happen if we apply a capacitance in phase b and then use same voltage for both phase. Dr. Ali Ki. pw --
Three generators rated as follows: G1: 100 MVA, 33 KV, sub-transient reactance of 10%; G2: 150 MVA, 32 KV, sub-transient reactance of 8% and G3: 110 MVA, 30 KV, sub transient reactance of 12%. reactance of G3 in per unit on a base of 100 MVA, 35 KV is Your answer reactance of G1 in per unit on a base of 200 MVA, 35 KV is Your answer reactance of G2 in per unit on a base of 50 MVA, 35 KV is Your answer
The statement given in which option related to transformers is wrong.A) Power transformers are used as step-down transformers in step-up consumption centers in production centers. B) Current transformers for measuring current at high voltageVoltage transformers are used to measure voltage. C) Voltage adjustment can be made with the on-load tap changing feature of power transformers. D) Transformers are of great importance in reducing power losses by increasing the power value in energy transmission. E) If there is no reactive power in energy transmission with direct current, the transformer cannot be used.