(a) (b) (c) List two types of an operational amplifiers. Find the Vour of the following operational amplifier circuit in Figure 1. R₂-10 k www V₁10v R₁= 2 KQ Figure 1 Vout Hint: Vout = - Vin] Modify the operational amplifier circuit in (b), so it can produce Vout= -15V, assuming Vin=30V. You also need to draw and explain your chosen values for the resistors

(a) (b) (c) List two types of an operational amplifiers. Find the Vour of the following operational amplifier circuit in Figure 1. R₂-10 k www V₁10v R₁= 2 KQ Figure 1 Vout Hint: Vout = - Vin] Modify the operational amplifier circuit in (b), so it can produce Vout= -15V, assuming Vin=30V. You also need to draw and explain your chosen values for the resistors

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

do H.W For the integrator op-Amp the input voltage is 015. Cos 100t, find, the value of Capacitor required to give peak op voltage is -5V. [R=1K5] Ans: C=1MF; if you Assume
- V2 15Vdo 3 U1A R1 2 1k V- LM324 1k V3 15Vde | VOFF = 0 VAMPL = 1 FREQ = 2k AC = 0 0. R2 Figure 4. Operational amplifier circuit. What frequency does the output voltage (across R3) have? What is the amplitude of the output voltage? From the output waveform and the input waveform, determine the gain of the op-amp circuit. Does this match with what you predicted? How could you change this circuit so that the output voltage would be nearly the same as the input voltage? What purpose would that serve? Can you modify the existing circuit and verify this experimentally? What is the phase difference between the output and input voltage? Derive the transfer function for the output-input relationship for the operational amplifier. How would the gain and the output change if a capacitor were in the feedback path instead of a resistor? (Examine the circuit using phasors and impedance and circuit analysis techniques). -w-
1. Use the figure below for the following questions. R = 10N and V is a 5V DC source that can provide a maximum of 1 mA of current. The op-amp is ideal. Vin R Vo What is V, in volts? Enter answer here 2. What is Iut in miliamps?
3K Calculate the the input Voltage of an inverting op-amp with the following parameters Rf = 1 MOhms, Ri = 20kOhms and Vo = 2V. a.3.47 mV b.-40 mV c.-3.47 mV d.40 mV
.
3ZF The typical value of the out impedance of an op-amp is a.between 100 Ohms to little less than 1 KOhms b.less than 100 Ohms c.at least 10 percent of the input impedance d.equivalent to short circuit
Please answer clearly
Q2 Calculate the voltage gain, output voltage, input impedance, and output impedance for the cascade amplifier of Figure. Ipss V, = -5 B = 450 = 18 +20 V 22 k2 0.5 uF 2.4 k 15 kQ 0.5uF ImV pss 0.05 uF 4.7 ka 3.3 M0 680 0 # 100 uF = 100 uF
Determine the maximum theoretical efficiency of RC-coupled class-A amplifier as shown in Figure Q2(a). Show every detail of the calculation steps. Vcc Ice R1 RL C2 IB R2 IE Figure Q2(a)
Q) Figure below amplifier .given the input wave FOrm Shows a Comperator Circuit Vs using 6 sin wt Volt. the output OPerational Sketch and label the input Voltage Vs and wave Forms Voi and Vo1 12 V tov -10V Vs - lov Vos -tov
Design a voltage follower amplifier circuit with a voltage divider on it. Assume that you have 60v voltage input voltage with a frequency of 60hz. Instead of using “Universal Op Amp 2" as a component, use the OPO7 Amplifier. What should be the values of your R1 and R2 to get a reading of a voltage output equal to 5.38 volts at exactly 20ms. The arrangement of your input should be, the one that is at the top most is the Voltage Input followed by the R1 and the lowest part is the R2. Draft17 Cursor 1 V(n005) Horz: 20.0054ms Vert: 5.3827036V What is the value of R2 in kilo ohms? No need to include the Units. R2 = k Ohms
(Q1) Design a circuit with Op-Amp when Vi 3v and Vo = 12v (i) Using Inverting Amplifier (ii) Using Non-Inverting Amplifier Assume any value if necessary.