Q.1. For hypereutectoid plain carbon steel (select %C content yourself), determine the phases that are present, the compositions of these phases, and the percentages or fractions of the phases. Make schematic sketches of the microstructure that would be observed for conditions of very slow cooling at the following temperatures: a) Just above the austenite transformation temperature b) The austenite transformation temperature 10°C c) The eutectoid transformation temperature +10°C d) The eutectoid transformation temperature 10°C -

Q.1. For hypereutectoid plain carbon steel (select %C content yourself), determine the phases that are present, the compositions of these phases, and the percentages or fractions of the phases. Make schematic sketches of the microstructure that would be observed for conditions of very slow cooling at the following temperatures: a) Just above the austenite transformation temperature b) The austenite transformation temperature 10°C c) The eutectoid transformation temperature +10°C d) The eutectoid transformation temperature 10°C -

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter6: Introduction To Mechanical Properties

Section: Chapter Questions

Problem 6.8P

See similar textbooks

Similar questions

As an Engineer describe the complete heat treatment required to produce a quenched and tempered steel microstructure contains 92% martensite and 8% Fe3C, the composition of the martensite is 1.10 C. Steel having a yield strength of at least 100000 psi. Include appropriate temperatures
4- A structural alloy has a rupture strength of 238N/mm?. Cold deformation amount is 34% after rupture. Find the true rupture strength of this alloy.
Using the isothermal transformation diagram for a 0.45 wt% C steel alloy (Figure 10.40), determine the final microstructure (in terms of just the microconstituents present) AND approximate percentages of the microconstituents that form in a small specimen that has been subjected to the following time-temperature treatments. In each case assume that the specimen begins at 845°C (1550°F), and that it has been held at this temperature long enough to have achieved a complete and homogeneous austenitic structure. (a) Rapidly cool to 250°C (480°F), hold for 10^3 s, then quench to room temperature. (b) Rapidly cool to 700°C (1290°F), hold for 30 s, then quench to room temperature. (c) Rapidly cool to 700°C (1290°F), hold at this temperature for 10^5 s, then quench to room temperature. (d) Rapidly cool to 400°C (750°F), hold for 500 s, then quench to room temperature.
Materials, properties and testing Describe the effect bend testing have on the thermal properties of steel.
Normal stress of alumi
Q.4. Give a reason for the following facts: 1- Ceramics fail after only about 0.1% strain under tensile test. 2- Porosity is an inherent defects in ceramics. 3- Ceramics carbides consider ideal choice for ceramic abrasives. 4- Orthoclase has the advantage over other types of feldspar.
Compare the difference in hardenability of plain carbon steels given below. Hardenability is the strengthening of steels by the process of quenching + tempering. Chemical compositions ( wt % ) C Mn P S Fe Steel 1 0.2 0.45 0.04 0.05 99.26 Steel 2 0.4 0.75 0.04 0.05 98.76 Steel 3 0.6 0.75 0.04 0.05 98.56
i need quickly please please please Which of these cast iron would allow the greatest amount of plastic deformation before fracture . Nodular cast iron Grey cast iron White cast iron None of them can be worked. If the diameter of steel specimen stretched by tension load is doubled , then it’s tensile strength will be Halved Remain unaffected Doubled Become four times Temperature is proportional with Percent of elongation Tensile strength Modulus of elasticity All above The tensile strength of a steel specimen that have a 182 HB , equals to 490 MPa 910 MPa 627 MPa Not given…
A batch of casted mild steel has a modulus of elasticity of 200 GPa and a yield strength of 250 MPa. Calculate for its modulus of resilience. After cold working the steel, the yield strength increases to 310 MPa. Calculate for the percent reduction in the average grain diameter given σo = 70 MPa and k = 0.74.
Which one of the following processes causes a dramatic increase in the hardness of a steel part? A) quenching B) tempering (c) normalizing D full annealing
In which cast-iron carbon exists in the form of Fe;C? A gray B white C) nodular (spheroidal) D malleable