For a 99.65 wt% Fe-0.35 wt% C alloy at a temperature just up the eutectoid teamperature, determine the following: (a) The fractions of each phases. (b) The Cooling curve for the specific alloy. (C) Descript the phases for this alloy.Subject: Metallurgy For a 99.65 wt% Fe-0.35 wt% C alloy at a temperature just up the eutectoid teamperature, determine the following:(a) The fractions of each phases.(b) The Cooling curve for the specific alloy.(C) Descript the phases for this alloy.y+ Fe;Ca + Fe;C6.700.35 0.76Composition (wt % C)Temperature

Given:- Co=0.35 % of CC1=0.022% of CC2=0.76% of CTo find:-a) Fractions of each phasesb) cooling…

99.65 wt% Fe-0.35 wt% C alloy at a temperature just up the eutectoid teamperature, determine the following: (a) The fractions of each phases. (b) The Cooling curve for the specific alloy. (C) Descript the phases for this alloy. Subject: Metallurgy

99.65 wt% Fe-0.35 wt% C alloy at a temperature just up the eutectoid teamperature, determine the following: (a) The fractions of each phases. (b) The Cooling curve for the specific alloy. (C) Descript the phases for this alloy. Subject: Metallurgy

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter5: Phase Transformations And Phase Diagrams

Section: Chapter Questions

Problem 5.17P

See similar textbooks

Related questions

Q: An aluminum pipe has a length of 65 m at a temperature of 16°C. An adjacent steel pipe at the same…

A: Given Data:Aluminum pipe has Length Lc=65mTemprature = 16°CCoefficient of thermal expansion steel…

Q: Example 9.36. Design a Zeolite-Softener for an industrial concern, using the following data : (i)…

Q: This is the loss in evapotranspiration

A: Evapotranspiration is the amount of water that is removed through the process of evaporation,…

Q: In wastewater treatment plants, ammonium ion is removed from the water by raising the pH to form…

A: a) The equilibrium reaction that describes the process of ammonium conversion to ammonia is given as

Q: The following information is given for cadmium at 1atm: boiling point = 765 °C Hvap(765 °C) = 100…

A: Given: Boiling point = 765°C Melting point = 321°C Specific heat solid= 0.230 J/g°C Specific heat…

Q: Which of the following materials has the highest thermal resistivity (R) value? O Steel Concrete…

A: Thermal resistivity is the ability of a material to resist the flow of heat through it. It is the…

Q: The sludge produced from the aeration tank of the activated sludge process has a solid content of 2%…

A: This question is related to the Environment Engineering from Civil Engineering.

Q: The enthalpy of vaporization of trichloromethane (chloroform, CHCl3) is 29.4 kJ mol−1 at its normal…

A: Given: The enthalpy of vaporization of trichloromethane (chloroform, CHCl3) is 29.4 kJ mol−1 at its…

Q: Water with 90 mg/L of a degradable contaminant flows through a reactor. The influent flow rate…

A: Given, Degradable contaminant flow,D0=90 mg/lFlow rate = 100 m3/dReactor Volume V=200 m3kd=1.0 d-1

Q: The second stage nitrification process is presented by the following equation Nitrobacter 2NO2+ 02…

Q: Calculate the percent volatility of the solids given that an empty container weighs 15.7g. A sample…

Q: Which of the following use oxygen in a confined space? O Microbial growth Oxyacetylene welding O…

A: Explanation : The oxygen deficiency in a confined space can be caused due to various factors. As…

Q: Which type of activated carbon is most suitable for gasoline vapor recovery?

A: The activated carbon is classified based on Characteristics of activated carbon Type of raw…

Q: For a steel alloy it has been determined that a carburizing heat treatment of 11.9 h duration will…

A: Given data: Steel alloy 1: Time taken for carburizing heat treatment (t1) = 11.9 hr Carbon…

Q: An aluminum pipe has a length of 50 m at a temperature of 6°C. An adjacent steel pipe at the same…

A: Concept Initial length = L1 at temperature T1 Due to temperature change to T2 length of the…

Q: The capillary rise (height) in mm of an ethanol having a viscosity of 0.032 J/m2. The tube has a…

Q: A sheet of BCC iron 1 mm thick was exposed to a carburizing gas atmosphere on one side and a…

A: Given:- The thickness of the sheet of BCC iron = 1 mm The carbon concentrations at the two surfaces…

Q: Derive the relation for adiabatic compressibility for ideal gas.

A: Here is the proof for adiabatic compressibility for ideal gas

Q: Stainless steel accessories in cars are usually plated with chromium to give them a shiny surface…

A: As, q = mc tf-t1So, 62.5 = 0.00 5 Kg C 50.8-23⇒ C = 62.50.0005 x 27.8⇒ C = 449.64 J/Kg K

Q: What is the solubility of ethane (in units of grams per liter) in water at 25 °C, when the C2H6 gas…

A: Given data: Partial pressure (P) = 356 mm Hg 1 mm Hg = 0.001316 atm P = 356 x 0.001316 = 0.468 atm

Q: An aluminum pipe has a length of 68 m at a temperature of 15°C. An adjacent steel pipe at the same…

Q: Effluent from an industry 'A' has a pH of 4.2. The effluent from another industry 'B' has double the…

Q: Provide relevant infomation about the constituents of OPC in the blank cells of the following uble…

A: The components are blended to one part of the clay and then crushed and ground into dry-style ball…

Q: Effluent from an industry 'A' has a pH of 4.2. The effluent from another industry '8' has double the…

Q: Calculate the dosage of activated carbon to reduce an influent (flowrate = 10 mgd) concentration of…

Q: The specific gravity is the -1 ratio of the weight of a given volume of the material to the weight…

Q: An aluminum pipe has a length of 60 m at a temperature of 10° C. An adjacent steel pipe at the same…

Q: The disinfection of water is carried out in a stirred tank. The treatment process has water as the…

A: Given: The input rate is 48000 L/h. The volume of tank is 3500 L. The rate of disinfectant is…

Q: ) Calculate the concentration of hydroxide ions *Select a concentration between 0.10 and 0.58 d)…

A: Calculation Solution of answer is in second step

Q: A water contains 3.5 mg/L of ferrous iron (Fe2+), 0.3 mg/L of manganese (Mn2+), and 0.7 mg/L of…

A: The given data is shown below: Ferrous iron=3.5 mg/LManganese=0.3 mg/LAmmonia=0.7 mg/LFree residual…

Q: [14] Electrolysis process is based on : thermal effect of current O chemical effect of current…

A: The process of decomposing ionic compounds into their constituent elements by running a direct…

Q: 3.A core sample is saturated with an oil (po = 35°API), gas and water. The initial weight of the…

A: ρo = 35° APIρw = 1 g/ccm1 = Initial weight of the sample = 224.14 gm2 = Weight of sample…

Q: What is the calculated value of the cell potential at 298K for an electrochemical cell with the…

A: Solution; Given Data; EAg+/Ay=+0.80, E°Al3+/Al=-1.66 vTherefore E°ceu=+0.80-(-1.66)…

Q: Effluent from an industry'A' has a pH of 4.2. The effluent from another industry 'B' has double the…

A: pH from industry A = 4.2 pH is defined as concentration of H+ ion. pH = -log[H+] 4.2 = - log[H+]…

Q: A vapor compression refrigeration cycle uses steam as the working fluid. Steamflows steadily with a…

Q: A.) What is the approximate concentration of free Ag+ ion at equilibrium when 1.43x10-2 mol silver…

A: Given: Concentration of AgNO3=1.43×10-2 MConcentration of CN-=1.08 M

Q: Calculate the amount of barium from Sodium sulphate in a liter. A 100 ml solution of sodium sulphate…

A: Given data There is 100 ml solution of Sodium sulphate is treated with solution of Barium chloride…

Q: 1. For added strength, many highways and buildings are constructed with reinforced concrete…

A: To define: Why it is important the thermal coefficient of concrete and steel to be same.

Q: What is the concentration, in grams per liter, of the chemical in water as it is filled?

Q: The sludge produced from the aeration tank of the activated sludge process has a solid content of 2%…

Q: An aluminum pipe has a length of 59 m at a temperature of 11°C. An adjacent steel pipe at the same…

Q: An aluminum pipe has a length of 54 m at a temperature of 10°C. An adjacent steel pipe at the same…

Q: Kerosene has a specific weight of γk = 51.1 lb/ft3 and benzene has a specific weight of γb = 56.2…

Q: An aluminum pipe has a length of 69 m at a temperature of 8°C. An adjacent steel pipe at the same…

A: Given, Length of aluminium pipe, Ls= 69m Initial temperature = Ti= 8°C Coefficient of thermal…

Q: This process occurs when both ice crystal and water droplets are in the cloud. O Collision O None of…

A: This process occurs when both ice crystal and water droplets are in the cloud. Ice crystal process

Q: -18. The solubility product of calcium fluoride (CaF) is 3.45 X 10-11 at 25°C. Will a fluoride…

Question

100%

For a 99.65 wt% Fe-0.35 wt% C alloy at a temperature just up the eutectoid teamperature, determine the following: (a) The fractions of each phases. (b) The Cooling curve for the specific alloy. (C) Descript the phases for this alloy. Subject: Metallurgy

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1 Solution:-

VIEW

Step 2 Solution:-

VIEW

Step 3 Answer:-

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Q.1. For hypereutectoid plain carbon steel (select %C content yourself), determine the phases that are present, the compositions of these phases, and the percentages or fractions of the phases. Make schematic sketches of the microstructure that would be observed for conditions of very slow cooling at the following temperatures: a) Just above the austenite transformation temperature b) The austenite transformation temperature 10°C c) The eutectoid transformation temperature +10°C d) The eutectoid transformation temperature 10°C
subject: Material Engineering Using the given sheet for the Ni-Ti Phase diagram, how many phase fields appear in the diagram and write down the weight fraction of gamma phase for an alloy containing 43% wt of Ti at 1000 C
View Policies Current Attempt in Progress Using the Animated Figure 10.40, the isothermal transformation diagram for a 0.45 wt% C steel alloy, specify the nature of the final microstructure (in terms of the microconstituents present) of a small specimen that has been subjected to the following temperature treatments. In each case assume that the specimen begins at 845 °C and that it has been held at this temperature long enough to have achieved a complete and homogeneous austenitic structure. a) Rapidly cool to 700 degrees C, hold for 100,000 s, then quench to room temperature. b) Rapidly cool to 450 degrees C, hold for 10 s, then quench to room temperature. proeutectoid ferrite + pearlite proeutectoid ferrite + martensite proeutectoid ferrite + pearlite + martensite eT proeutectoid ferrite + pearlite + bainite + martensite all spheroidite Save all bainite Attempts: 0 of 5 used Submit Answer all martensite bainite + martensite
A steel alloy is known to contain 93.8 wt% Fe, 6.0 wt% Ni, and 0.2 wt% C. Assume that there are no alterations in the positions of other phase boundaries with the addition of Ni. (a) What is the approximate eutectoid temperature of this alloy? i °C (b) What is the proeutectoid phase when this alloy is cooled to a temperature just below the eutectoid? (c) Compute the relative amounts of the proeutectoid phase and pearlite. i Wp i
Compare the difference in hardenability of plain carbon steels given below. Hardenability is the strengthening of steels by the process of quenching + tempering. Chemical compositions ( wt % ) C Mn P S Fe Steel 1 0.2 0.45 0.04 0.05 99.26 Steel 2 0.4 0.75 0.04 0.05 98.76 Steel 3 0.6 0.75 0.04 0.05 98.56
1. A 65 wt% Ni -35 wt% Cu alloy is heated to a temperature within the a + liquid phase region. If the composition of the a phase is 70 wt % Ni, determine i. The temperature of the alloy ii. The composition of the liquid phase iii. The mass fraction of both phases Composition (at% Ni) 20 40 60 80 100 1600 H 2800 1500 Liquid 1453°C 2600 1400 Solidus line Liquidus line 2400 1300 a +L 1200 2200 1100 A 2000 1085°C 1000 20 40 60 80 100 (Cu) Composition (wt% Ni) (Ni) Temperature (°C) Temperature (F)
Q.4. Give a reason for the following facts: 1- Ceramics fail after only about 0.1% strain under tensile test. 2- Porosity is an inherent defects in ceramics. 3- Ceramics carbides consider ideal choice for ceramic abrasives. 4- Orthoclase has the advantage over other types of feldspar.
For alloys of two hypothetical metals A and B, there exist an a, A-rich phase and a ß, B-rich phase. From the mass fractions of both phases for two different alloys (given below), which are at the same temperature, determine the composition of the phase boundary (or solubility limit) for the following: Fraction Fraction Alloy Composition a Phase B Phase 60 wt% A - 40 wt% B 0.59 0.41 30 wt% A - 70 wt% B 0.13 0.87 (a) a phase wt% A (b) B phase wt% A
The assembly consists of a brass shell (1) fully bonded to a solid ceramic core (2). The brass shell [E = 115 GPa, a = 18.7 × 10-6/°C] has dout 50mm. and din = 35mm. The ceramic core [E = 290 GPa, α = 3.1 x 10-6/°C] has a diameter dout = 35mm. At a temperature of 15°C, the assembly is unstressed. AT = 60°C. Find the internal stress in the brass. = 200 mm Brass shell (1) (2) Ceramic core
(a) What is the characteristic feature of the shape memory alloys? (b) Define high entropy alloys. (C) How many solid phase(s) form(s) as a result of the nonvariant ternary eutectic reaction in lead-free ternary eutectic solders? (d) What are the biodegradable alloys?
As an Engineer describe the complete heat treatment required to produce a quenched and tempered steel microstructure contains 92% martensite and 8% Fe3C, the composition of the martensite is 1.10 C. Steel having a yield strength of at least 100000 psi. Include appropriate temperatures
Question 3 For a 40 wt% Sn-60 wt% Pb alloy at 150 °C and taking the densities of Pb and Sn at 150 °C to be 11.23 and 7.24 g/cm?, respectively. Composition Cats Sn) 20 60 100 327C 600 300 Liquid 500 232'C 200 400 183°C 18.3 61.9 97.8 300 100 200 100 60 80 100 (Pb) Composition (wt% Sn) (Sn) The lead-tin phase diagram a) AN6 marks b) W c) calculate raction. CROmarks d) calculate the relative amount of each phase present in terms of mass fraction volume fraction Temperature ("C) Temperature (F)