Problem 3 The figure presents the portion of the pipe network through which a fluid with a specific gravity of 1.0X is flowing. At junction B, the pressure is 100 kPa. Junction A is located 2 m higher than Junction B while the elevations at Junctions B and D are the same. The friction factor of this pipe system is 0.0001, and all pipes have the same diameter of 50 cm. The length of pipe AB is 100 m, and the length of pipe BC is 200 m. Please determine the pressures at Junctions A and D If your ID is 0155497, the specific gravity will be specified as 1.07. A 0.2 m³/s 0.5 m³/s 0.2 m³/s B E 0.1 m³/s

Problem 3 The figure presents the portion of the pipe network through which a fluid with a specific gravity of 1.0X is flowing. At junction B, the pressure is 100 kPa. Junction A is located 2 m higher than Junction B while the elevations at Junctions B and D are the same. The friction factor of this pipe system is 0.0001, and all pipes have the same diameter of 50 cm. The length of pipe AB is 100 m, and the length of pipe BC is 200 m. Please determine the pressures at Junctions A and D If your ID is 0155497, the specific gravity will be specified as 1.07. A 0.2 m³/s 0.5 m³/s 0.2 m³/s B E 0.1 m³/s

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q2: An otl of viscosity Co.15 pas) and specific gravity 0.9 is flows Throngh 1.Find The slope of The Pipe That will canse The Pressure to be constantalong The pipes entire length? an inclined (300mm) diameter Pipe. Q= 0.005m3/sec 3oomm Dia. Zz datum 2. check if The Rlow is laminarRlow?
A valve is suddenly closed in 200 mm diameter pipe. The increase in pressure is 700 kPa. Assuming that the pipe is rigid and the bulk modulus of water is 2.07 x10° Compute the maximum discharge.
Q2) i Neglecting minor losses in the pipe, determine the flows in the pipes and 0 the pressure heads at the nodes (kinematic viscosity= 1.13x104m?¥s) F E n I I 30 Data Pipe Ab BC O DE EF AF BE Lengeh (m) 600 600 200 600 600 200 200 Diameter (wm) 250 150 100 150 150 200 100 Roughness size of all pipes = 0.06 mm Pressure head elevation at A = 70 i o.d. Elevation of pipe nodes A 5 c D L ® 028 0 20 2 2
Oil with sp. gr. 0.95 flows at 200 lit/sec through a 500 m of 200 mm diameter pipe (? = 0.0225). Determine (a) the head loss (m) and (b) the pressure drop (kPa) if the pipe slopes down at 10⁰ in the direction of flow.
2. A tank and piping system are shown below. The total length of PVC pipe is 2500 ft and discharges water into the atmosphere. The pipeline has an open globe valve and four threaded elbows; h1 = 10 ft and h2 = 45 ft." a. If the discharge is 0.5 cfs, what NPS should be used for the PVC pipe (ks = 0.00006 inch). b. What is the pressure at A, the midpoint of the pipeline? c. Draw the EGL and HGL. h2 Water T = 10°C (50°F) Globe valve
A pipe carrying oil of sp gr 0 877 changes in A pipe carrying oil of sp gr 0.877 changes in size from 150mm at section E to 450mm at section R Section E is 3 66m lower than R section R. Section E is 3.66m lower than R and the pressures are 91.0kPa and 60.3kPa, respectively. If the discharge is 0.146m3 respectively. If the discharge is 0.146m /s, determine the lost head and the direction of flow.
Figure Q4 shows there are two sections of pipes in the system, which are 38m long of 5 cm diameter pipe in section 1 and 45 m long of 15 cm diameter pipe in section 2. The friction factor of pipe in section 1 and 2 are 0.005 and 0.003 respectively. The entrance of the pipe is sharp and the change of section at point C is sudden. There are two 90-degree elbows and an open globe valve in the system. The fitting loss coefficient, k are 0.9 for each 90-degree elbow and 0.25 for open globe valve. If the exit elevation is zero and the flow rate of water is 0.005 m/s. i. Name all the losses in the system with the formula involved, Calculate the total losses in the system, Calculate the power extracted by the turbine if the turbine is 75 ii. iii. percent efficient. 30m Elevation Pipe section 1: 5cm diameter with 38 m long Орen globe Turbine Elevation Om Pipe section 2: 15cm diameter with 45 m long
Problem 9-36 pipe bend shown is in a horizontal plane. A fluid weighing 8.615 kN/m enters the bend with a velocity of 3.5 m/s and a pressure of 280 kPa. Neglecting head loss, find the force required to hold the bend in place. The Ans 10.4 kN 65 200 mm O 80 mm diam
29 REVIEW INNOVATIONS 2. A pipe 977 m long branches into 3 pipes at junction A. The three pipes span 1046 m, 885 m, and 796 m. They come together at junction B and continue as a single pipe for 1224 m. All pipes are 300 mm in size except the shortest one which is 250 mm. The pressure drop between the junctions is 260 kPa. Friction factor "f" can be assumed 0.02 in the entire system. Calculate the rates of flow in the branching pipes.
Problem 6: EGL and HGL (II) Part A Why is the energy gradient (i.e., the slope of the EGL=EL) larger in pipe 2 than in pipes 1 or 3? (<10 words) Part B Why are the EGL and HGL not parallel in this figure? (<10 words) H V² 28 HGL 2 EL Hydraulic grade line, slope = S, Ax - Energy line, slope = Sy Bed ylope Datum h₂ - Az 2 4 X
The diameter of a pipe changes gradually from 6 inches at A to 18 inches at B. A is 15 ft lower than B. If the pressure at A is 10 lbs per square inch and at B, 7 lbs per square inch when there are 5.0 cubic ft per second flowing, determine: a. the direction of flow. b. the frictional loss between the two points B. If in Problem 1 the direction of flow is reversed, determine the pressure at A if all other factors, including the frictional loss, remain the same. C. In Problem 1, determine the diameter of pipe at B in order that the pressure at that point will also be 10 lbs per square inch, all other factors remaining constant. D. Determine the discharge in Problem 1, assuming no frictional loss, all other conditions remaining as stated. E. What would be the difference in pressure in pounds per square inch between A and B, Problem 1, if there were 6.2 cubic ft per second flowing, neglecting friction.
Q-Water flows through a pipe having an inner radius of 10 mm at the rate of 36 kg/hr at 25° C. The viscosity of water at 25°C is 0.001 kg/m.s. The Reynolds number of the flow is