Select a tension diagonal member of A36 steel [ F= 58 ksi ]. The axial tension is 50k dead load and 16 k live load and the member is 13 ft long. Assume 34" - diameter bolts will be located on a single gage line. Assume the preferable limit on slenderness ratio L/r is 280: - - Select the lightest single angle member. Select the lightest double angle member having legs separated by 1/4" Gusset plates

Select a tension diagonal member of A36 steel [ F= 58 ksi ]. The axial tension is 50k dead load and 16 k live load and the member is 13 ft long. Assume 34" - diameter bolts will be located on a single gage line. Assume the preferable limit on slenderness ratio L/r is 280: - - Select the lightest single angle member. Select the lightest double angle member having legs separated by 1/4" Gusset plates

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter4: Compression Members

Section: Chapter Questions

Problem 4.4.2P

See similar textbooks

Similar questions

If the beam in Problem 5.5-9 i5 braced at A, B, and C, compute for the unbr Cb aced length AC (same as Cb for unbraced length CB). Do not include the beam weight in the loading. a. Use the unfactored service loads. b. Use factored loads.
A W14X120 is used as a tension member in atruss. The flanges of the member are connected to a gusset plate by 3/4 inch boltas shown below. Use A36 steel with Fy-36 ksi and Fu=58 ksi Determine the Yielding Capacity of the section based on LRFD (kips) Determine the Tensile Rupture capacity of the section based on LRFD Determine the Demand to Governing Capacity Ratio (based on yielding and rupture only) if the Demand load carried by the section are DL=200 kips LL=400 kips use LRFD Properties and Dimension Ag=35.30 in^2 x = 6.24 in ry= 3.74 in d=14.5 in tf=0.94 in bf=14.7 in tw=0.59 in k=1.54 d=14.5 Y k1=1.5 bf=14.7 tf-0.94 X -tw=0.59 H
Please solve the ff and write legibly SN = 38 Determine the adequacy of the W8x58 subject to the following: Axial Tension: DL = 100 kN + SN, LL = 120KN + SN Axial Compression: DL = 60 kN + SN, LL = 80KN + SN L = 8m 2 holes for 20mm.dia. bolts Fy = 250 Mpa Fu = 400 Mpa
A bolted connection shown is bolted with a A-325 bolts with an allowable shearing stress of 207 MPa. A-36 steel is used. The applied force "T" is equally divided among the bolts. Assume bolt hole diameter to be 3 mm bigger than bolt diameter. Diameter of bolt is 20 mm. T/2 T T/2 10 mr 10 mm T/2 300 mm T/2 Determine the capacity of the connection if shearing governs in kN. A 1548.58 B 1170.56 1290.62 D 1439.25 000
ASSIGNMENT #5 BIAXIAL BENDING Problem: Check the beam shown for compliance with the NSCP Specification. Lateral support is provided only at the ends, and A992 steel is used, F, = 345 mPa. The 90 kN service loads are 30% dead load and 70% live load. a. Use LRFD b. Use ASD d tw by ty 1x(106) S(10³) mm mm mm mm³ mm mmª W410x100 415 10 260 16.9 398 1920 SECTION Tx mm 177 1m 90 kN 90 KN 1.5m W410x100 I Loaded Section Ly(106) Sy(10³) Ty mmª mm³ mm 49.5 381 62.4 1m Zx(10³) Zy(10³) mm³ mm³ 2130 581
Question 1 Check that the medium-term load of 38 kN applied to the spaced column shown in below complies with the design requirements of BS 5268-2. The column consists of two 38 x 150 C22 timbers 76 mm apart. All joints are glued and intermediate packs are 250 mm long. suitable connection #### x ->89² 6:38. Y T -end blocking AP 100 intermediate blocking L₂ 1₁ x W L W EFH 400 m 38kN medium term load -ICHICHID -200 600 600 600 600 600 600 200 38kN medium term load
2. A single-angle tension member, an L3x3 x3/8, is connected to a gusset plate with 22mm- diameter bolts as shown in the figure. A36 steel is used. The service loads are 155KN dead load and 66 kN live load. Investigate this member for compliance with the NSCP 2015 Specification. Assume that the effective net area is 85% of the computed net area. Consider yielding of the gross section and fracture of the net section. Neglect block shear. a. Use LRFD. b. Use ASD L3½x 3/2 x% Section