Problem 1.5: A source voltage of 240 Vs is applied to a 30Z30° ohms load impedance. Find the average current, rms current, peak current, and aver- age power delivered to the load. Problem 1.6: A coil having an inductance of 30 mH and resistance of 3 Q is connected to a 120-V, 60-Hz source. Determine the kWh energy drawn by the coil in an 8-hour period.

Problem 1.5: A source voltage of 240 Vs is applied to a 30Z30° ohms load impedance. Find the average current, rms current, peak current, and aver- age power delivered to the load. Problem 1.6: A coil having an inductance of 30 mH and resistance of 3 Q is connected to a 120-V, 60-Hz source. Determine the kWh energy drawn by the coil in an 8-hour period.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.16P: A single-phase, 120V(rms),60Hz source supplies power to a series R-L circuit consisting of R=10 and...

See similar textbooks

Similar questions

A single-phase, 120V(rms),60Hz source supplies power to a series R-L circuit consisting of R=10 and L=40mH. (a) Determine the power factor of the circuit and state whether it is lagging or leading. (b) Determine the real and reactive power absorbed by the load. (c) Calculate the peak magnetic energy Wint stored in the inductor by using the expression Wint=L(Irms)2 and check whether the reactive power Q=Wint is satisfied. (Note: The instantaneous magnetic energy storage fluctuates between zero and the peak energy. This energy must be sent twice each cycle to the load from the source by means of reactive power flows.)
Draw the sinusoidal waveform of the AC voltage and current for the given loads below. Describe the characteristics of the waveform for each load. A. Pure resistor B. Pure inductor C. Pure capacitor
Q2. For the circuit shown below, sketch the current waveforms iş and io and determine the Average and RMS for both currents. a = 50° TI 50 2 Vs = 300 sin 100zt ( cot T2 in cot
Solve for 20 V rms supply. Thank you.
A single phase AC chopper supplies a pure inductive load of 0.02H from 220V, 50HZ AC supply. The triggering angle of the thyristors is 100°. (Assume the circuit is ideal.) a. Sketch the circuit b. Develop the load current expression and find the decay angle of the load current c. Sketch the load voltage and load current waveforms d. Calculate the RMS value of load voltage e. Calculate the RMS value of load current f. If the triggering angle of the thyristors is chosen as 60°. Explain the operation of the circuit.
15 A of current is taken by a non-inductive load at 125 V. In order that the same current shall be generated from 240 V, 50 Hz mains. An inductor is now also then connected in series. Note: The resistance of the inductor should be ignored and also assume the waveform to be sinusoidal. Determine the phase difference between the current and the applied voltage, the impedance of the circuit and the inductance of the inductor.
1-Choose the correct statement for pure resistor connected across single phase AC supply. a. Current and Voltage are in phase b. Current leads the supply voltage by 90° c. None of these d. Current lags the supply voltage by 90° 2-Identify the current through the inductor in a RL transient circuit connected across DC voltage, when the switch is kept open. a. 0 b. Infinity c. V/R d. 1
Q2. For the circuit shown below, sketch the current waveforms is and io and determine the Average and RMS for both currents. ot io Vs = 220V a = 220° + ot 1002
A single-phase motor draws 220 W at a power factor of 0.8 lagging when connected across a 240 V rms, 60-Hz source. A capacitor is connected in parallel with the load to produce a unity power factor. Determine the required capacitance.
1.6. The resistance of a coil is 140 2 and its inductance 0.85 H. Determine the current, the p.f. and the circuit impedance when the coil is connected to 120 V, 60 Hz supply.
A single-phase AC voltage controller has a resistive load R = 10 Ohm, and the RMS input voltage is Vs = 230 V, 60 Hz. The delay angle is 120 degree. Then power factor of the circuit is: Select one: O a. 1 O b. 0.75 O c. 0.44 O d. None of the above O e. 0.9
1- When connected in series with a pure resistor R with resistance r and inductance L, three pairs of currents are 5A with a sinusoidal voltage application with an effective value of 100V. The voltage across the coil and resistor element is 80V and 30V. a-Find the power and power consumed by the coil alone? b- Find the power consumed by the system and the power factor? c- Draw the voltage triangle, impedance triangle and power triangle?