For the circuit shown in the following figure, a) Find and draw the Thévenin equivalent circuit at terminals a-b. b) A load impedance Z, is connected to the Thévenin equivalent circuit. Calculate the value of Z, such that it absorbs maximum average real power, and indicate the type the load (Inductive or Capacitive) c) Calculate the average real power absorbed by Z. bcosllot)V 3 IH

For the circuit shown in the following figure, a) Find and draw the Thévenin equivalent circuit at terminals a-b. b) A load impedance Z, is connected to the Thévenin equivalent circuit. Calculate the value of Z, such that it absorbs maximum average real power, and indicate the type the load (Inductive or Capacitive) c) Calculate the average real power absorbed by Z. bcosllot)V 3 IH

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.22P: The real power delivered by a source to two impedances, Z1=4+j5 and Z2=10 connected in parallel, is...

See similar textbooks

Similar questions

The real power delivered by a source to two impedances, Z1=4+j5 and Z2=10 connected in parallel, is 1000 W. Determine (a) the real power absorbed by each of the impedances and (b) the source current.
Let a series RLC network be connected to a source voltage V, drawing a current I. (a) In terms of the load impedance Z=ZZ, find expressions for P and Q, from complex power considerations. (b) Express p(t) in terms of P and Q, by choosing i(t)=2Icost. (c) For the case of Z=R+jL+1/jC, interpret the result of part (b) in terms of P,QL, and Qc. In particular, if 2LC=1, when the inductive and capacitive reactances cancel, comment on what happens.
Is the power factor in Question 6 a leading or lagging power factor? Explain your answer.
Consider a load impedance of Z=jwL connected to a voltage and V let the current drawn be I. (a) Develop an expression for the reactive power Q in terms of ,L, and I, from complex power considerations. (b) Let the instantaneous current be i(t)=2Icos(t+). Obtain an expression for the instantaneous power p(t) into L, and then express it in terms of Q. (c) Comment on the average real power P supplied to the inductor and the instantaneous power supplied.
15 A of current is taken by a non-inductive load at 125 V. In order that the same current shall be generated from 240 V, 50 Hz mains. An inductor is now also then connected in series. Note: The resistance of the inductor should be ignored and also assume the waveform to be sinusoidal. Determine the phase difference between the current and the applied voltage, the impedance of the circuit and the inductance of the inductor.
The values of the elements for the given circuit are given below.The maximum average power that can be transferred to the ZL load iswhich one?R1 = 400 OhmsL = 1000j OhmsR2 = 500 Ohms
Q3 (a) Given a circuit in Figure Q3(a); Determine the load impedance, Zı that results in maximum average power transferred to ZL. (i) (ii) Find the maximum average power transferred to the load impedance. jl 2 1220° V ZL -jl 2 Figure Q3(a)
For the circuit given in Figure 1, a) Find the Thevenin equivalent circuit with respect to terminals a-b b) When a 5000 resistor is connected to terminal a-b, find the voltage on the resistor wwwwwwmm c) It will be connected to a-b terminals and its voltage on 5000 load will be 132 kV rms. What should be the capacitive reactance value that will increase it? wwwwwwwww d) What happens to the short-circuit current when the a-b terminals are short-circuited? 2+1202 000 m da 127/6 kV rms ob 1.5 +/902 000 w 12725 kV ms
AC Circuits Current, Voltage, Power, Power Factor and Phasor Diagrams. Consider the circuit shown in Figure 3. (i) Find the total impedance ZT as seen by the voltage source. (ii) Find the total current IT supplied by the source. (iii) Sketch phasor diagram of Vs and IT and State whether IT leads or lags Vs (iv) Determine the power factor angle for the circuit. 9. L R1 1002 0.213H IT Vs R3 1502 C 12020°V 22µF 60HZ R2 50Ω Figure 3 Answers |(1) Zr = (ii) IT= (iii)
XL=62 R1=40 Is R2=90 + + E1=100V20° AC R3=80 V3 Xc=72 ZT a. Calculate the total impedance (ZT). b. Compute the source current (Is). c. Find the current across the capacitor Xc. d. Calculate the voltage across the resistor R3. e. Find the average power delivered to the circuit (PT). f. Find the total power factor (Fp).
2)With reference to the waveform given below formulate the equation for the average value of DC voltage available across the load, if the load connected is a pure resistive load and if the circuit applicable to this waveform is fed from a load having 180 ohm 50 Hz start connected input with the value of resistance equivalent to 200 ohm solve and obtain the value of Dc power in the load (3 phase bridge) Van Vbn Ven P 180° 210° 360° - Vm D1 & D2 DI&D6 D3 & D6 D3&D4 D5&D4 D5&D2 120° 120°
d. 565.685 V If a Load absorbs 20 kVA at a leading power factor of 0.6. Then the complex power is: Select one: O a. 12000 - j16000 VA O b.-12000 + j16000 VA O c. 12000 + j16000 VA O d. None of these Given the circuit below and the associated set of voltages and currents, the reactive Power developed by im voltage source is FENG300 MINTERM