(c) Given a network with the load power shown in Figure Q3(c). Determine: (i) the supply voltage, Vs. the required capacitive element value in parallel with the 36 kW load to raise the power factor of this load to 0.9 (lagging). (ii) 0.12 jo.3 2 36 kW 24kW Vs (+ 0.88 pf lagging 24020° V rms 0.82 pf lagging Figure Q3(c)

(c) Given a network with the load power shown in Figure Q3(c). Determine: (i) the supply voltage, Vs. the required capacitive element value in parallel with the 36 kW load to raise the power factor of this load to 0.9 (lagging). (ii) 0.12 jo.3 2 36 kW 24kW Vs (+ 0.88 pf lagging 24020° V rms 0.82 pf lagging Figure Q3(c)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Solve it quickly please
Question 3 What is the value of real power supplied by the source in the figure? ww 30/0º V rms | C 40 3031.4 None of the answers 2007.8 5252.8
Resistive Voltage The supply across the terminals of this circuit is 170 V, 50 Hz. An ammeter is connected to the supply. ww000 R L The inductance L is 0mH. The ammeter reading the supply current shows 4 A. Find the magnitude of the voltage across the resistance: V. • Use Impedances and Complex Numbers. • Use Ohm's Law. Meters read Magnitude.
1. For the circuit in Figure 1: a) What is the RMS-value, zero-phase angle and frequency of voltage source e(t)? b) What is the total impedance of the circuit? c) Calculate frequency domain voltage Uc and current lot. (present solution in polar form x < yᵒ). d) Calculate time domain voltage uc(t) and current io(t) (present solution as sine-wave function of time) e(t) = 170 sin (100лt + 25°) V, R1 = 102, C = 15 µF 12 e(t) (1) Figure 1. T 1 ↑ U tot H R UR C HH U₁
A factory has a large induction heater operating at 1000 V, 50Hz. The current flowing intothe heater is 12.33 A RMS and the true power is 10 kW b) Calculate the reactive power, apparent power and the power factor (PF) for this load.c) If the PF is lower than 0.9, explain the problem from an electrical perspective thencalculate how this load could be balanced practically.d) Draw a diagram to illustrate where the capacitor needs to be placed and what hashappened to the reactive current that was originally flowing from the inductive load backto the supplier? What are the specifications for this capacitor? What would such acapacitor cost? Who could supply this type of component?
2. A voltage applied to a load is V=208 4 20°V and current through load is I=10 a–10° A. Find the following [SO 1] o complex power consumed by load o Is the load inductive or capacitive? o the power factor of the load o the reactive power consumed or generated by the load. o Does the load consume or supply reactive power?
Question-2 Can you throw the emergency solution? I would appreciate it if you write legibly.
Q3. For the circuit shown below, sketch the current waveforms iş and io and determine the Average and RMS for both currents. i, 1:1 ɑi = 15° Vs = 220 V az = 250° ot i. 302 VR ot 2n
Two loads connected in parallel take a total of 2.4 kW with a lag fp of 0.8, from a line at 120 V rms and 60 Hz. of the loads absorbs 1.5kW with lagged fp of 0.707. Deter- mine: a) the fp of the second charge, b) the element in parallel required to correct the fp of the two charges and convert it to behind 0.9.
d) Two areas of a power system with characteristics shown in Table Q3.1 are connected via a tie line as shown in Figure Q3.1. R (p.u.) D (p.u.) SB (MVA) i) ii) AREA 1 Tie-line Figure Q3.1 Table Q3.1 Area 1 0.02 0.8 500 AREA 2 The interconnected system is operating in steady state at a frequency of 50 Hz with 100 MW flowing from Area 1 to Area 2 when a step increase of 100 MW in load occurs in Area 1. Following the increase in load in Area 1 and using a 1000 MVA base calculate: The new system frequency in Hz. The new tie line power flow in MW. Area 2 0.04 1.0 1000
Which one of the following statements is true: The purpose of the power-factor correction is to add inductive elements to keep real power at a minimum level. The purpose of the power-factor correction is to add resistive elements (typically resistances) to improve the total reactive power. The purpose of the power-factor correction is to add reactive components (typically capacitive) to establish a system power factor closer to unity. The purpose of the power-factor correction is to add resistive elements (typically resistances) to establish a system power factor closer to zero.
In the figure below, all impedances are in ohms, all voltages are in volts and currents in Amperes. Both sources operate at 60 Hz. X, = 200 n X, = 600 n 80 sin (wt + T/2) x, = 600 2 0.2 ain wt Determine the time dependent current i (A) due to the current Choose... source Determine the time dependent current (A) flowing through the inductance with a Choose... reactance of 200 Ohms due to the current source Determine the time dependent current i (A) due to the voltage Choose... source Choose... Determine the total effective current (A) flowing through the Choose... inductance with a reactance of 200 Ohms