In Industry, three Inductive loads, each of resistance R = 26 ohms and inductance L= 0.08 H are connected in Delta to a 410 V, F = 50 Hz, 3 phase supply. Find the following below: Phase Impedance, Zp %3D Phase Voltage, Vp = Phase current, Ip = Line current, lL= The Total Power Consumed, P =

In Industry, three Inductive loads, each of resistance R = 26 ohms and inductance L= 0.08 H are connected in Delta to a 410 V, F = 50 Hz, 3 phase supply. Find the following below: Phase Impedance, Zp %3D Phase Voltage, Vp = Phase current, Ip = Line current, lL= The Total Power Consumed, P =

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.7P: Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor,...

See similar textbooks

Related questions

Q: A 3- phase star connected load has resistance of 4 Ω, inductance of 15.9mH & a capacitive reactance…

A: Need to find you totla current, total power absorbed and Phasors

Q: V. A series circuit of two pure elements has the following applied voltages and resulting currents…

Q: 16. A wye connected load has a 5L20° ohm impedance per phase 120 volts three-phase source. Calculate…

A: In this question we will find line current of star connection...Series connected RC circuit…

Q: A coil of wire having a value of (5 + j8) ohms is connected in series with a capacitive reactance…

Q: 2. An impedance of 4-j3 ohms is connected in parallel with an ideal inductor L across a 110V, 60hz…

A: We need to find out value of inductance for given condition in the given circuit

Q: A coil of wire having a value of (5 + j8) ohms is connected in series with a capacitive reactance…

A: A coil (5 + j8) ohms with in series with a capacitive reactance Xc, this series combination is then…

Q: Z1 V1 3PH 120V 60HZ

Q: A 4-kW, 110-Vrms load, as shown below, has a power factor of 0.82 lagging. Find the value of the…

Q: 41. Ideal inductors and capacitors are in phase with each other. True False "By the convention…

Q: each of resistance R = 30 ohms and inductance L = 0.12 H are connected in Delta to a 430 V, F = 50…

Q: A non-reactive resistance of 60 Ω is connected in series with a 36 µF capacitor in each phase of a…

Q: 1. Given a Parallel Resistive - Inductive circuit as shown, determine the: 240 V 60 Hz R 152 = =…

A: Given A parallel resistive - inductive circuit. We need to determine the inductance of the…

Q: In phasor, the resistance has an angle of 90 degrees and the voltage and current are in phase."…

A: 73. Resistance R has only real value with zero imaginary value so resistance has zero degree not 90…

Q: In Industry, three Inductive loads, each of resistance R = 26 ohms and inductance L = %3D %3D 0.1 H…

A: Given

Q: Show your solution for this problem. A 400V, 3-phase star connected alternator supplies a…

Q: Three impedances are connected, each consisting of a resistance of (5) and an inductive reactance It…

A: According to the guideline we need to solve only the first three sub-parts.to According to the…

Q: A 120V (rms), 60HZ three-phase system is supplying power to the following two loads: Load # 1: A…

Q: 50 Hz, 250 V single phase power line has the following loads placed across it in parallel; 4 kW at a…

A: Using power triangle relations find active and reactive power of each load then add them to get…

Q: In Industry, three Inductive loads each of resistance R = 29 ohms and inductance L= %3D 0.06 H are…

A: In the Star Connection, the 3 winding's similar endpoints are connected to a common point known as…

Q: In Industry, three Inductive loads each of resistance R = 20 ohms and inductance L 0.04 H are…

Q: 1) Answer the following questions. a) As an engineer, you have been given a task to determine…

Q: In Industry, three Inductive loads each of resistance R = 33 ohms and inductance L = 0.11 H are…

A: A star connected load has, Per phase resistance (Rph)= 33 ohm Per phase inductance (Lph)= 0.11 H…

Q: A 440Vrms, 60-Hz source supplies two loads connected in parallel : Load 1(L1): 12 kVA, 0.70 pf…

Q: A 270 kV, three phase transmission line vith a 430 km length. The series mpedance Z =(0.345+j0.794)…

A: Transmission line parameters are given Find the T and π model equivalent circuit parameters

Q: BA series-connected load draws a current i(t) = 4 cos(315t + 10°) A when the applied voltage is v(t)…

A: According to question we have to calculate the value of Apparent power, power factor and value of…

Q: H.w A 3-phase , 50HZ , 132 KV overhead transm conductor diameter of 4 cm each , are arrange plane as…

A: In the above question a 3-phase, 50 Hz, 132 Kv overhead transmission lines has conductor diameter 4…

Q: Problem 2 For the circuit shown below: a) Determine Zr, I, VR, VL, and Vc in phasor form. b)…

Q: In Industry, three Inductive loads each of resistance R = 21 ohms and inductance L = 0.1 H are…

Q: Three non-inductive resistances, each of 100 Q, are connected in star to a three phase,…

A: Active power consumed by inductor is zero. Eventhough inductors connected in parallel, active power…

Q: Task A2 Power factor correction In an AC circuit, the current flowing through Load A is found to be…

A: The current flowing though the load is: 15 <9.20 A. The voltage across the load is 240<620 V…

Q: The balanced system below has a phase voltage of 120 V. It supplies a balanced load Z1 that has…

A: In this question we need to find a total reactive power and true power of the given three phase…

Q: The currents in each branch of a two-branched parallel circuit are given by the expression 1₁ = 7.07…

Q: In Industry, three Inductive loads each of resistance R = 28 ohms and inductance L = 0.07 H are…

A: As per the honor code I will do only first three parts of the question. Kindly repost the other…

Q: In Industry, three Inductive loads each of resistance R 29 ohms and inductance L 0.09 H are…

Q: A)- Determine the line currents and phase voltages. *Determine the lamp resistances by Ohm's Law,…

A: Given data, The power consumed by the lamp is 25 Watt. The average voltage VP is 27.20 V The…

Q: 6.8. A three phase, 50 Hz, 100 km transmission line has resistance 0.1 ohms/km, inductance 111.7…

A: 3 phase transmission line: L=100Km; f=50 Hz; resistance is : r=0.1Ω/Km; R=10Ω inductance is:…

Q: Question one A balanced star connected load comprises of 20 ohm resistance and 0.07 Henry inductance…

A: Given that Rph=20 ohmLph=0.07 Hf=50 HzVL=415V Calculate the indctive reactance…

Q: A source with 240 Vms, 50 Hz is connected in parallel to the three loads. These loads can be…

A: In this question we will find total load ,power factor and capacitance value for improving power…

Q: 9. a) Find Zin for the following circuit at w = 100 rad/sec. 20 N 10 2 Zin 2 mF 0.1 H b) A balanced…

Q: In Industry, three Inductive loads each of resistance = 32 ohms and inductance L = 0.16 H are…

A: According to question: a) Phase impedance…

Q: In Industry, three Inductive loads, each of resistance R = 22 ohms and inductance L = 0.07 H in…

Q: . For the circuit given below Find Thevenin equivalent circuit Find maximum average power delivered…

A: According to Thevenin's theorem, any linear circuit, no matter how complicated, may be simplified to…

Q: In Industry, three Inductive loads, each of resistance R = 32 ohms and inductance L = 0.04 H are…

A: As per Bartleby guidelines we are allowed to solve only three subparts, please ask the rest again.

Q: Q20. A 250V, 60 Hz supply inductive-capacitive circuit with Xe 38.52 consumes 1600W i) If the…

A: Frequency f 60Hz Voltage v =250V

Q: 14. Three resistances, each of 500 2 are connected in star to a 400-V, 50-Hz, 3-phase supply. If…

Q: Given a mesh connected system with reactive factor of 60 percent and true power of 2,500 kW.…

A: We need to find out reactive power

Q: Q5: Three-phase, 50 Hz, 132 KV power system of equivalent impedance 10+j35 N with load 110+j29 Q.…

Q: H.W: Each phase of a balanced three-phase -connected load consists of a 200 mH inductor in series…

Q: In Industry, three Inductive loads each of resistance R= 24 ohms and inductance L = 0.13 H are…

A: Resistors, inductors and capacitors form an integral part of any electrical circuit. A source,…

Q: 3) Suppose a voltage ?(?) = 2 × 120 sin(377? + 30°) is applied to a single phase load, and the…

Concept explainers

Single Phase AC Circuit

Alternating Current (AC) is a type of electric power in which the electric current changes, both in magnitude and direction, at regular intervals. This AC Circuits can deliver power in either a Single Phase system or a Three Phase system.

Question

In Industry, three Inductive loads, each of
resistance R = 26 ohms and inductance L =
0.08 H are connected in Delta to a 410 V, F =
50 Hz, 3 phase supply.
Find the following below:
Phase Impedance, Zp =
Phase Voltage, Vp =
Phase current, Ip =
Line current, IL=
The Total Power Consumed, P =

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 5 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Analysis of Single Phase and Three Phase System

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor, and a 4 capacitor. (a) Draw the circuit diagram. (b) Compute the series impedance. (C) Determine the current I delivered by the source. Is the current lagging or leading the source voltage? What is the power factor of this circuit?
Impedances Z2 and Z3 in parallel are supply. Z1 =6.25 + j 1.25 ohm; Z2 = 5 + j0 ohm and Z3 = 5 – jXc ohm. Determine the value of capacitance of Xc such that the total current of the circuit will be in phase with the total voltage. When is then the circuit current and power. series with impedance Z1 across a 100 V, 50 Hz ac
Which component of impedance is not dependent on the frequency of the source of voltage? A. capacitance reactance B. inductive reactance C. resistance D. all are independent of the frequency of the source
An inductive reactance of 6 ohm is connected in series with a parallel combination of a variable resistor R and a capacitive reactance of 15 ohm across 100V , 50 hz supply. a. Solve for the frequency so that the magnitude of the inductive reactance is 2 times the magnitude of capacitive reactance. b. Solve for the value of R so that the total current I will be maximum.
1. Find the current and voltages Vr,Vl and Vc in phasor form. 2. Verify the kirchoffs volatage law around the closed loop. 3. Find the power factor of the circuit and indicate whether it os leading or lagging
A resistance of 20 Ω, an inductance of 0.2H and a capacitance of 100μF are connected in series across 220-V 50 Hz mains. Determine the following: a) impedance b) current c) voltage across R, L, and C d) power in watts and VA e) power factor and angle of lag.
The admittance of a circuit is (0.03-j0.04) Siemens. Find the value of resistance and inductive reactance of the circuit if they are joined a)in series and b) in parallel.
Three Impedances each of (9 - j18)N are connected in mesh across a three-phase 415V ac supply. Determine the phase current, line current, active power, reactive power drawn from supply. Also draw the Phasor diagram for the mesh connection and marks the Line current ,phase current line voltage and phase angle between phase current and pahse voltage. phase current (Ip) Line current real power reactive power
When a resistor is connected across the terminals of an ac generator (117 V) that has a fixed frequency, there is a current of 0.332 A in the resistor. When an inductor is connected across the terminals of the same generator, there is a current of 0.365 A in the inductor. When both the resistor and the inductor are connected in series between the terminals of this generator, what is (a) the impedance of the series combination and (b) the phase angle between the current and the voltage of the generator? Note: The ac current and voltage are rms values and power is an average value unless indicated otherwise. (a) Number (b) Number Buda i Vrms R Irms.R Circuit 1 Units Units Vrms. Irms, L Circuit 2 > L Vrms R www Circuit 3
Impedances Z2 and Z3 in parallel are in series with impedance Z1 across a 100 V, 50 Hz ac supply. Z1 =6.25 + j1.25 ohm; Z2 = 5+ j0 ohm and Z3 = 5-jXc ohm. Determine the value of capacitance of Xc such that the total curent of the circuit will be in phase with the total voltage. When is then the circuit current and power.
find total equivalent resistance and reactance and total impedance transferred in primary side.
Impedance of AC circuit and Admittance of AC circuitSHOW THE CIRCUIT USING ANY SOFTWARE OR YOU CAN DRAW IT MANUAALYY thNAKSS