P6.13. Reflection and transmission at a transmission-line discontinuity. In the system shown in Fig. 6.71, an incident wave of voltage V+ strikes the discontinuity from the left, that is, from line 1. Find the reflected wave voltage and current into line 1 and the transmitted wave voltage and current into line 2. 428 Chapter 6 Transmission-Line Essentials for Digital Electronics R₂ = 1500 ww 0 Line 1 (+) Line 2 R₁ = 100 2 Z01 = 100 Z02 = 50 2 FIGURE 6.71 For Problem P6.13.

P6.13. Reflection and transmission at a transmission-line discontinuity. In the system shown in Fig. 6.71, an incident wave of voltage V+ strikes the discontinuity from the left, that is, from line 1. Find the reflected wave voltage and current into line 1 and the transmitted wave voltage and current into line 2. 428 Chapter 6 Transmission-Line Essentials for Digital Electronics R₂ = 1500 ww 0 Line 1 (+) Line 2 R₁ = 100 2 Z01 = 100 Z02 = 50 2 FIGURE 6.71 For Problem P6.13.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Example 6 The EMF and current waves of a circuit having resistance only are e=170sin27 60t and i=14.14sin 27 60t. Determine. a.) Equation of power wave b.) Frequency of power wave c.) Maximum value of power wave Average power d.) e.) Power when t=1/480 sec, 1/240 sec, 1/90 sec. f.) Draw voltage, current and power waves.
Discuss the methods used to minimize inductance in transmission lines and their effects on signal transmission.
A 2 V signal is incident to the interface from a 75 Ohm region propagating to a 50 Ohm impedance region. What is the reflection coefficient? What is value of the incident, reflected and transmitted wave? What voltage would you measure on either side of the interface right after the signal goes through the interface.
1) how did the soution for the collector current become VCC/(Re+Rc)? please explain 2.)instead of using the boxed solution, would it be alright to use KVL instead to solve for the collector current? If yes, please show the equation for the KVL.
Phase shift due to finite length of circuit conductors. On a particular type of circuit board, assume a signal travels at 2/3 of the speed of light. Suppose a high-speed system using this type of board can tolerate a phase shift in a sine-wave signal due to propagation delay of only 15° before failing to work. Calculate the maximum length /MAX (in m, or a suitable subdivision such as cm or mm) that a circuit-board trace carrying this signal can have at each of the following frequencies without encountering excessive phase shift due to the propagation delay along the trace: (a) f=10MHz, (b) f=30MHz, (c) f=500 MHz, and (d) f=2.5 GHz.
Could you please go more in depth about how to create the ac equivalant model? thank you
b) If quantity A is PATAT with TC of 2mV/C, and quantity B is CTAT with TC of -1mVrC, then determine the following quantities if they are PTAT or CTAT 1. 1/A 2. 1/B 3. A+ 5°B
This question from micorowave system course.
In an AC LVDT system, measuring the output voltage alone gives anindication of the displacement from the center, but not the direction ofdisplacement. Explain why, and also explain a method for solving thisproblem.
In the Transmission Line Simulator, the Transmission Line is composed of which parameter/s? O A. The Shunt Conductance Only O B. The Series Impedance and Shunt Capacitance O C. The Shunt Capacitance Only O D. The Series Impedance Only
A wave signal travelling along an electrical transmission line (usually called incident wave) will be reflected back in the opposite direction when the travelling signal encounters a discontinuity in the characteristic impe- dance. This can happen in real life if we join dissimilar transmission lines together. Signals travelling alone the line will be partially reflected at the junction (see illustration below; note that up to this point we have not asked you any question yet). Impedance Discontinuity Forward Current Propagating Voltage Wave Z01 Zo2 Return Current Z01 Zo2 Incident Wave Transmitted Wave Reflected Wave Transmission Line Reflection Suppose a transmission line with characteristic impedance Zo is terminated at one end with an impedance of ZL (recall that impedance is a complex number Z = X +iY where X is the resistance and Y is the reactance), then the reflection coefficient I' is given by the voltage reflection equation ZL – Zo ZL + Zo where I, ZL = XL + iYL, and Zo Xo +…
1. For the given circuit in Figure 6.21, R= 2702, L = 1mH, input Vs = 4Vpp (sinusoidal), Vs %3D a) Calculate/Measure VRms, VLms, Ims for 1KHZ, 20kHz and 100kHz. (PW and Lab Part) Figure 6.21 b) Calculate/Measure the phase difference when frequency = 20 kHz. (PW and Lab Part) c) Calculate/Measure the impedance of the inductor at 20kHz and obtain the phasor diagram using the related values you calculated in the previous step. Calculate the apparent power, true power and reactive power related to each component in the circuit. (PW and Lab Part) a) for f=1KHZ PW Lab For f-1kHz Calculated Measured Vrms Vcrms Irms