please provide me the answers for these questions What is the maximum power that can be drawn from a 1.50-V battery with an internal resistance of 0.30 ohm?The maximum power cannot be determined without knowing the resistance of the external circuit.O 7.5 WO 0.675 WO 0.45 WO 5.0 WO O Part AA 4.00-kg block rests on a 30.0° incline as shown in the figure. If the coefficient of static friction between the block and the incline is 0.700, what magnitude horizontal force F must act on theblock to start it moving up the incline?F30.0°O 84.0 NO 51.1 NO 76.4 NO 54.7 NO 34.0 N

V = IR I = V/R = 1.50/0.30 = 5 Amp power = P = VI = 5 * 1.5 = 7.5 W Option 1st is the wright answer

Answered: O The maximum power cannot be…

O The maximum power cannot be determined without knowing the resistance of the external circui O 7.5 W O 0.675 W O 0.45 W O 5.0 W

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Actually, (a) and (b) were incorrect I already submitted it with a and b then I got the result…

A: Concurrent force system is a system of forces in which line of action of all the forces passes…

Q: Assume the below given figure as unit length to be equal to 10 mm, draw the isometric views of…

Q: You are a graduating mechanical engineering student. As part of the course requirement, you applied…

A: In engineering, dimensionless numbers are used to represent the relationship between the model and…

Q: sketch the front, top, and right-side views of the objects shown in exercise 2.1 and 2.2.

A: The given question contains orthographic projections. Orthographic projections are the diagrams…

Q: Our mechanical engineering student and your instructor are at it again, this time with the student…

A: Curve is given and we will revolve it around the y-axis to get the solid body.We will use the method…

Q: i cant read this.. can you write it out??

Q: Q1: Explain the electronic distribution of germanium, iron and magnesium if you know that their…

A: Solution to question (1) as per our Company policy:

Q: A cable hangs between two poles that are 70-ft apart. The two poles are both 40 foot high. Sag is…

Q: A metal is heated up to a temperature of 500 degrees Celsius. It is then exposed to a temperature of…

A: The time required to reach .Given:The initial temperature of the metal is .The surrounding's…

Q: Can you give the step by step formula?

Q: Ideal crystals are always have imperfections in a crystal structur

A: No, ideal crystal does not have imperfections.

Q: Assume F-9 kN. Using RECTANGULAR COMPONENTS, determine the direction of the resultant force,…

A: To find: The direction of the resultant measure counter clockwise from the positive x-axis. Given:…

Q: Q2: Select physical dimensions and produce engineering parts list You are to select two deep groove…

A: The Answer is below

Q: Create a free hand isometric drawing of the three objects

A: Free hand isometric drawing of all three components are drawn below...

Q: Reminder: Kindly show the complete step-by-step solution. Please make sure that your handwriting is…

A: Given: To determine the moment about Point A. Moment is defined as the product of force and the…

Q: or columns should be the sum of when we place integers starting from 1 in a magic square of size…

Q: If 1 ton of bituminous coal is burned to generate electricity, how many kWh could be produced if the…

A: Dear student, There are two different problems that you have posted but…

Q: Given the points A( – 5, 6, – 4), B( – 2, — 10, 6), and C(4, 0, 5), find (a) the angle between AB →…

Q: Shown in the image is a vertical section of a 66 block grid of a gold mine deposit. Each block is…

A: Based on the image presented, which includes varying ore grades ranging from 1.4 g/t to 2.9 g/t in…

Q: There is a light pole on one bank of a small pond. You are standing up while fishing on the other…

A: Given:The height of the light pole is The height of the man is The distance between the light pole…

Q: A 90° elbow shown in Figure 5 (a) is to direct water flow upward at a rate of 50 kg/s. The water is…

Q: The piston diameter of a 6-stroke 1-cylinder gasoline engine is given as 4.25 inch mm, the piston…

Q: A hammer is balanced at the point "A", close to the metal part. If this hammer is then cut along the…

A: Consider the diagram shown below for the hammer with the center of masses for each side.

Q: Degree of drawing is measured in terms of; Reduction in strain Reduction in area O Reduction in…

A: Degree of drawing is measured in terms of: Answer: Reduction in area

Q: Why you put h= 19 instead of h=38 your answer for the exercise is incorrect can you please correct…

Q: Solve the following problem and show your complete solutions. 1. An alloy steel having a diameter of…

A: Stress is proportional to strain.Please go through hand written solution.

Q: A washer has a hole in the middle. (a) As the washer is heated, does the hole expand, shrink, or…

A: Effect of temperature on the metals: When metals are heated they expand or shrink based on their…

Q: -450.76 for parts (c) and (d) are incorrect.

A: To determine:c)The gauge pressure at point 2d)The gauge pressure at point 3

Q: If you know that the effect of the effect of reaction reaction to the year in shape is located along…

Q: ) A long, small diameter tube is shown below. The top end of the tube is closed. The bottom end is…

A: The data given is Atmospheric pressure, Patm= 1 atm = 101325 N/m2 = 14.7 psi L1 = 20 in. = 0.508 L2…

Q: In (Eigure 1). F-700 N and @-20 Figure 30 FA-700 N 1 of 1 Determine the magnitude of the resultant…

A: If F= 700 N and thita= 20°Determine the magnitude of the resultant force.Determine the direction of…

Q: Hello, I need help with the answer of 3.14 from the picture, please.

Q: A line in a drawing is 3 inches long, when measured. If the drawing scale is 20:1, how long is that…

A: Given Data The length of line is:3 inches The drawing scale is:20:1 To find: The actual length of…

Q: If I have 2.4 kg of Silver that I need to melt at the melting point , how much heat needs to be…

A: Given data: m = 2.4 kg Lf = 88300 J/kg Need to determine the heat required for melting.

Q: Can you pls slove this question briefly with hand written notes and diagram

Q: Part A - Construction of Mohr's circle for the state of stress For the element shown, construct…

A: Given Data

Q: Give the steps by steps explanation of the previous answer

Q: Write your answers to the following blanks. The Charpy impact experiment is through the process of…

A: The charpy impact test is used to determine the amount of energy absorbed by a material during…

Q: Round off the following number to three significant figures:2553N

A: SIgnificant digits show the value of a number in limited digits. Significants digits are very…

Q: To help workers in your project site move dozens of equipment weighing 70 kgs to a height of 2.2m,…

Q: 1- If you are driving a car at a speed of 100 km/hr and you look away for two seconds, what is the…

Q: What is going on?

Q: rity is 10 m/s²?

A: Given Mass m = 3 kg Acceleration due to gravity, g= 10 m/s^2

Q: diameter 10 cm.

A: Detailed answer shown below

Q: I asked for problems 6 and 7 to be answered, but I did not get a properly structured answered as the…

A: Chamfer the edge at 45o with 0.250” leg distance.

Q: 20 cm 30 cm

A: This is the case of the forced vortex motion. here radius = 0.3 m distance between the two limb del…

Question

please provide me the answers for these questions

What is the maximum power that can be drawn from a 1.50-V battery with an internal resistance of 0.30 ohm?
The maximum power cannot be determined without knowing the resistance of the external circuit.
O 7.5 W
O 0.675 W
O 0.45 W
O 5.0 W
O O

Part A
A 4.00-kg block rests on a 30.0° incline as shown in the figure. If the coefficient of static friction between the block and the incline is 0.700, what magnitude horizontal force F must act on the
block to start it moving up the incline?
F
30.0°
O 84.0 N
O 51.1 N
O 76.4 N
O 54.7 N
O 34.0 N

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

That is the answer I already have, I am lookinf for the answers to the blanks in the image
Q5: For the below shaded area, calculate Ixand Kx 130 mm 30 mm 30 mm -40 mm -40 mm-
It's saying this is not correct. Thank you for your help.
The piston diameter of a 6-stroke 1-cylinder gasoline engine is given as 4.25 inch mm, the piston stroke is given as 3.75 inch. Since the compression ratio of this engine is 9.5, find the stroke volume, combustion chamber volume and cylinder volume in cm3.
An electric hot water heater consumes 3.1 kilowatts of electricity and converts it to heat. How long will it take the water heater to heat a 67 gallon tank of water from 10 degrees Celsius to 50 degrees Celsius? (1 kilogram of water is 0.37 gallons, 1 Calorie = 4200 J). It may be helpful to refer back to the weekly handout for guidance on this problem. Your final answer should be in minutes (rounded to the nearest 10 minutes).
The first diagram is wrong, line AB should be longer since its length is equal to 580mm than line P2B which is equal to 360mm, please revise.
Q1 (а) A tall standpipe as shown in Figure Q1(a) with an open top has an inner diameter 7 d=2.1 m and wall thickness t= 20 mm, Given the weight density of water y = 9.81 kN/m³ and water pressure is p = y h, calculate the height h of water that will produce a circumferential stress of 12 MPa in the wall of the standpipe. (i) (ii) Calculate the axial stress in the wall of the tank due to the water pressure.
As per NPCP, a shower compartment or bath shall have a minimum interior area of 0.6 sqm and it shall be capable of encompassing a 762 mm diameter circle. What shall be the least possible length in millimeters of the shower compartment assuming it is rectangular in shape? (round off your answer to the nearest hundredth and write your answer in this format : 000.00 mm)
The attached answer was provided for the attached question. The equation uses the given temperature in celcius and the answer is also given in celcius. The temperature was used in the equation without converting from F and the answer was supposed to be in F. I am worried that even if I converted the answer to celcius that it would be correct because temperature was used in the equation using the incorrect unit.
I need answer within 20 minutes please please with my best wishes
Part I. Shorter problems focused on the fundamentals a. For the image at the right, the coordinate angles are a = 57°, ẞ= 121°, y=49°, and the point along a-a is (15,-6,3). What is the angle between lines a-a and b-b? Z b-b B LL F a (x,y,z) a-a Y b. If the magnitude of the force, F-3121bf, what is the magnitude projected along the a-a axis? y
Can you pls help me solve this. A 3 meter-high room is heated through a vertical steam pipe. If the bulk temperature of steam in the room was 25 degrees Celsius when the steam in the pipe is 98 degrees Celsius. determine (a) the minimum dimension of the pipe that could generate a power of 725 Watts if the pipe is (b) square and (c) circle •Pls answer with complete and detailed solution (3 decimal places all final answers with correct units) •Sketch an illustration/diagram with labels (this is a must; for a better understanding) Thank you I will give your answer a LIKE for helping me...