Hello, I need help with the answer of 3.14 from the picture, please.

Q: A hydraulic jack has a 2-inch diameter input piston and a 2-inch diameter output piston. If a 300 lb…

A:

Q: the sketch top, front, and right side isometric below. For the objects shown in sure that your views…

A: According to the details provided in the question we need to draw three projection view of the given…

Q: Statics Question The diagram shows 2 vectors. Solve for the resultant vector (force and…

A:

Q: rection: Locate the center of gravity in figures A & B by putting a dot or a point in each of the…

A: centre of garvity is the point where the gravitational force is acting through

Q: The dot product of two unit vectors: (The answer cannot be found on the other choices.) always has a…

A: When the dot product of any two vectors is equals to 1 then those vectors are in same direction…

Q: Q) Find Xc and Ye angle 10 m 20m 25 m

A: The Center of mass is a point where the sum of the moment of the weight of each particle is zero. It…

Q: 1.27. Which quadrant does the point P (-0.4, 1.5) lies? A. Quadrant I B. Quadrant Il C. Quadrant III…

A: (+,+) I quadrent (+,-)IV quadrent (-,-)III quadrent (-,+)II quadrent

Q: Our mechanical engineering student and your instructor are at it again, this time with the student…

A: Curve is given and we will revolve it around the y-axis to get the solid body.We will use the method…

Q: The figure shows the chain drive of a bicycle. How far will the bicycle move if the pedals are…

A:

Q: Given the isometric drawing, draw the multiview projection. The multiview projection of the glass…

A: Draw the isometric view.

Q: D Question 2 Express the force TBC as a vector (in terms of i, j, k). Show all calculations on your…

A: Express the force TBC as a vector (in terms of i, j, k). Show all calculations on your paper and…

Q: Q3/ For the plate shown in figure below find (a) E A Y수 4 6 X 7 5

A: Let us consider the given figure , divide into two parts of area A1 and A2 The sum of area ΣA can be…

Q: Q2: Select physical dimensions and produce engineering parts list You are to select two deep groove…

A: The Answer is below

Q: Given the points A( – 5, 6, – 4), B( – 2, — 10, 6), and C(4, 0, 5), find (a) the angle between AB →…

A:

Q: Direction: Locate the center of gravity in figures A & B by putting a dot or a point in each of the…

A:

Q: NOTE: Equal grades for each question will have (20 Marks) Q1: Find a unite vector perpendicular to…

A: A vector is an amount that has both extent, as well as course. A vector that has a size of 1 is a…

Q: The piston diameter of a 6-stroke 1-cylinder gasoline engine is given as 4.25 inch mm, the piston…

A:

Q: So 180 200 30 Find F and location 200

A:

Q: The figure below has the following weight per length. W₁ = 150 lb/ft W₂ = 175 lb/ft W3 = 130 lb/ft…

A: given;   w1=150lb/ftw2=175lb/ftw3=130lb/ftAB=1ftBC=6ftCD=4ftDE=5ftEF=8ftlets take reaction force at…

Q: 19. Find the resultant and angle of the figure shown below. 1120 N

A:

Q: H.W: Find the Trigonometric functi

A: given:find the trigonometric functions sinx,cosx,tanxwhen x=(0,45)

Q: please calculate at least 3 decimal places a) Draw a sketch where you replace the distributed…

A:

Q: For problems 1 and 2 below, using the Parallelogram method only (no other method will be accepted)…

A:

Q: For the blue shaded area shown in the image below, if dimension a = determine its area moment of…

A:

Q: Q5: For the below shaded area, calculate kand Kr 130 mm 30 mm 30 mm 40 mm 40 mm

A:

Q: The result that I got after solving it was 463.0721, is that correct?

A: Given: d= 0.27in τ capacity=26.5 ksi = 26500 psi. Factor of safety =1.6 To find: The maximum T-force…

Q: From the projected views obtain the isometric drawing.

A: According to the details provided in the question, there are three views of the first angle of…

Q: The distance between two stations A and B is 100 kilometers and its equivalent distance on the…

A: Given dataDistance between two stations D = 100KmLenght on the drawing sheet = 2.5cmMaximum length L…

Q: axis of the solid. Draw its projections, sectional front view & true shape of the section. Also…

A:

Q: A cube has an edge length of 7 cm. If it is divided up into 1-cm cubes, how many 1-cm cubes are…

A: Given   Base cube edge 7 cm Segregated cube edge 1 cm To find How many cubes are their

Q: Find Rab for the circuit fn figure. 202 202 Rab 792 252

A: The circuit is shown below.

Q: Find a "flat" object in your house, make necessary measurements, and then calculate the center of…

A:

Q: Given two points; (4,17) and (-4,1) on a line, what is the slope of the line? A. 2 B 1/2 C 1/2 D 2

A: Given Data A(4,17) B(-4,1)

Q: Q1/b/ * Q1/b): If at location B the car move at constant velocity.. So the angle a equal to: * 30…

A:

Q: If the horizontal distance was measured to be 130m and the inclination angle was 25 degrees, what is…

A: Considering a line AB having an inclination angle with horizontal of 25 degrees. The horizontal…

Q: On the first picture, you have the length of the triangle as 300. If the total length of the door is…

A: Here you are asking why the length of the triangle is 300 and not 440.

Q: To help workers in your project site move dozens of equipment weighing 70 kgs to a height of 2.2m,…

A:

Q: Isn't the area of the circle equal to pi times the square of its radius?

A: Explanation: Since the diameter ( d )  of steel bar is given, area of the circle is in terms of…