20 cm 30 cm

Q: A meter stick balances horizontally on a knife-edge at the 50.0 cm mark. With two 4.78 g coins…

A:

Q: When calculating "I", why have you used 50^3 x 24 rather than 24^3 x 50?

A: You have asked, When calculating "I", why have you used 50^3 x 24 rather than 24^3 x 50?

Q: Draw the isometric 70 R 30 50 60 40 40 30 60

A:

Q: The following is a schematic diagram of the Charpy impact tester. Is from the following. At this…

A:

Q: 3. During tug of war, the bicep muscle generated 4k N force that was perpendicular to the forearm…

A:

Q: Calculate the magnitude

A: The provided force system is shown below.

Q: Why do most materials exhibit an increase in dimensions when heated?

A: Thermal Expansion of material : When the material heated it gets expands is called as thermal…

Q: 2 m C 2.5 m 125 mm 1.5 m 25 kN/m 2 m 4 m

A: To determine the reaction at A and B, the beam can be dealt in two sections that are AD and DB. In…

Q: =o7 Cm) findSmax. tor Figure 0,7 Cm) fin mox. tor tigure tigure. 225 mm J0omm

A: Given Data The force acting in the downward direction is: F=400 N The height of the weld is: h=0.7…

Q: Enumerate at least 20 G-CODES and 10 M-CODES and write their description. Create a table to organize…

A: Given question: Enumerate at least 20 G-CODES and 10 M-CODES and write their description G Codes are…

Q: The pipe assembly shown is subjected to a force F= 600 N. The pipe has an inner diameter of 20 mm…

A: Consider the Free Body Diagram: Torque,T=600*0.2 =120 N.mTorque acting on part BC,TBC=120 N.mTorque…

Q: The first moment of an area (mm3) about the x-axis (Qx) is O 462,000 O 594,000 O 246,000 864,000

A:

Q: 1. The built-up beam pictured on the right is subjected to an internal moment of M = 75 kNm. a) At…

A: *The internal moment acting on the structure is M=75 kNm. *The total length of the T section is…

Q: The volume of a rectangular solid is determined from measurements of its length, height and breadth.…

A: To calculate the volume of the rectangular solid, we use the formula: V = L x H x B Where V is the…

Q: shown in Fig. 2-13.2a. The inscribed grid with each square having a length of 1 ft locates each…

A:

Q: determine and plot the moment M rotate arm 0A over the range 0 < Find the maximum value of M and

A:

Q: 8- When the sum of the forces acting on a particle is zero, the adjustment will be very large. O…

A: When the sum of forces acted on a particle is zero then the particle is in equilibrium. According to…

Q: 200 MPa 100 MPa 300 MPa

A:

Q: How would density be used to determine the concentration of antifreeze in the cooling system of an…

A: The density of antifreeze in the cooling system of automobiles is used to determine the…

Q: 10 mm Y 15 mm 30 mm 40 mm 10 mm 15 mm X

A:

Q: For an object of spherical shape, the value of critical radius would be

A: Given: Spherical shape body

Q: Q3/ Consider a point in a structural member that is subjected to plane stress. Normal and shear…

A:

Q: 100 mm 100 mm 10 mm 10 mm. 200 mm 100 mm f 10 mm I II

A: For the selection of sections, we have to calculate the maximum bending stress in the beam. From the…

Q: What is the reading below, in mm

A:

Q: Perform unit conversion. 28.9 nm to μm

A: Given 28.9 nm To be find Convert to μm

Q: The magnitude of F₁ is 58.7 The angle for F₁ is 0₁ 909.36 XN X

A:

Q: 8. For the cross-section of a beam shown; a) locate the centroidal axis from the bottom of the…

A:

Q: Shape factor S=M/N, N isShape factor S=M/N, N is

A: Shape factor defines the ratio of the under which two surfaces project over one another.

Q: Both pulleys are fixed to the shaft and as the shaft turn with constant angular velocity, the power…

A: power of pully A= power of pully BGiven θ= 0°(T1-T2)×RA =(T3-T4)×RB(80-65)×40…

Q: 4 ft A 2 ft 4 ft 2 ft The engine hoist shown above support a 1.2 kip engine, with a center of…

A: Given: The engine load, W = 1.2 kip

Q: 300 N 36 mm

A: We need to apply force equlibirium equation along the horizontal direction∑Fx=0Ax-C=0......consider…

Q: - 2- 45 100lbs/ft 300lb 30 200lbs

A:

Q: 3mm Imm 2mm 2mm 2mm

A: Let us divide the given figure into 3 sections as shown below – Section 1 is OBCO which is a…

Q: Instructions (PART 2): Draw the shear and bending moment diagram of each beam loaded as shown. Show…

A:

Properties of Fluids

The term fluid represents a type of substance that can easily change its shape under any external pressure/force and can flow. Fluids can acquire any shape in which it is stored and can resist normal stresses but cannot resist shear stress in rest condition. Whenever external shear stress is applied to fluids, it starts to flow. The fluids may be liquid or gas. Example- water, air, etc.