Select a V-belt drive to transmit 10 kW of power froma pulley of 200 mm diameter mounted on an electric motor running at 720 rpm to another pulley mounted on compressor running at 200 rpm. The service is heavy duty varying from 10 hours to 14 hours per day and centre distance between centre of pulleys is 600 mm.

Select a V-belt drive to transmit 10 kW of power froma pulley of 200 mm diameter mounted on an electric motor running at 720 rpm to another pulley mounted on compressor running at 200 rpm. The service is heavy duty varying from 10 hours to 14 hours per day and centre distance between centre of pulleys is 600 mm.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Problem 4. For the belt drive shown below calculate the contact angle 0, if: D %3D 100 mт; d 3 30 тm; C = 300 mm. D-d 20 sin V4c² - (D – d)²- -1 D-d sin 20 Op
A belt conveyor transports 18 tonnes per hr at 20°. Determine the unit weight of belt material in kg/ply-cm width-m to lift the load vertically up sufficient to give 33.5 m horizontal center-to-center pulley distance. 1750-rpm motor, V-belt drive to helical gear speed reducer. Belt speed, 61 m/min. Discharge over tail pulley. No tripper.
A 60 hp air pump blower in 18hr/day service running at a speed of 500 rpm is driven by means of a multiple v-belt drive which is powered by a compressor-stator motor with speed 1300 rpm. The center distance must be between 30 to 40 inches and the available driver sheave diameter iS 14 inches. Recommend a multiple v-belt drive that respects the following condition stated.
A hammer mill is driven by a High Torque (HT) AC motor. The system is used for 8 hours /day. Input speed is 870 RPM and input power is 25 HP. Nominal output speed is 310 RPM. Design a V-belt drive and specify:(a) (b) (c) (d) (e)the belt size,the sheave sizes,the number of belts, theactualoutputspeed,the center distance. Show all your calculations.
Select a suitable Vbelt drive for a flour mill transmitting power from a motor of 10 kW rotating at 1,440 rpm using suitable charts. The mill rotates at 400 rpm for a service of 22hrs per day and is to be arranged in minimum space with center distance of 0.5m. Assume that the pitch diameter of small pulley is 100mm.
A blower is driven by an electric motor though a belt drive. The motor runs at 750 r.p.m. For this power transmission, a flat belt of 8 mm thickness and 250 mm width is used. The diameter of the motor pulley is 350 mm and that of the blower pulley 1350 mm. The center distance between these pulleys is 1350 mm and an open belt configuration is adopted. The pulleys are made out of cast iron. The frictional coefficient between the belt and pulley is 0.35 and the permissible stress for the belt material can be taken as 2.5 N/mm2 with sufficient factor of safety. The mass of a belt is 2 kg per meter length. Find the maximum power transmitted without belt slipping in any one of the pulleys.
A blower is driven by an electric motor though a belt drive. The motor runs at 750 r.p.m. For this power transmission, a flat belt of 8 mm thickness and 250 mm width is used. The diameter of the motor pulley is 350 mm and that of the blower pulley 1350 mm. The center distance between these pulleys is 1350 mm and an open belt configuration is adopted. The pulleys are made out of cast iron. The frictional coefficient between the belt and pulley is 0.35 and the permissible stress for the belt material can be taken as 2.5 N/mm2 with sufficient factor of safety. The mass of a belt is 2 kg per meter length. Find the maximum power transmitted without belt slipping in any one of the pulleys. Note: Sketch the belt drive system for both parts and label the given data on it.
Problem: A pump is driven by an electric motor through an open type flat belt drive. Determine the belt specificationsfor the following data.Motor pulley diameter= 400 mmPump pulley diameter = 800 mmCoefficient of friction for motor pulley = 0.30Coefficient of friction for pump pulley = 0.35Center distance between the pulleys=2000 mmRotational speed of the motor=2000 rpmPower transmission = 40kWdensity of belt material = 1000 kg/m3 width of the belt=240mmthickness of the belt = 5mm
A1. A flat belt drive for speed reduction has pulley diameters of 200 mm and 380 mm. Themaximum belt tension is not to exceed 620 N and it is required to transmit 1·8 kW at anoutput speed of 360 rev/min. Determine:(a) The input torque. (b) The belt speed. (c) The limiting slack side tension. (d) The initial tension at which the belt should be set.
A chain drive is desired to couple a gearmotor with a bucket elevator. The 40 hp. gearmotor will operate at 350 rpm and the elevator drive shaft must operate as close to 60 rpm as possible. Select an appropriate chain size, commercially available sprockets, and number of links for a chain. Also calculate the actual chain speed and the center distance.
A shaft turning 150 RPM is to drive another shaft at 200 RPM. Find the diameters of the two pulleys, using integral number of inches for each diameter, to give as nearly as possible a belt speed of 2500 FPM. Please provide illustration.
2. A 75 kW induction motor runs at 740 rpm in clockwise direction. A 19 tooth helical pinion with20 degree normal pressure angle, 10 mm normal module and a helix angle of 23 degree is keyed to the motor shaft. Draw a 3-dimensional sketch of the motor shaft and the pinion. Show the forces acting on the pinion and the bearing at A and B. The thrust should be taken out at A All dimensions are in mm y 750 B 200 Z2=38 Z₁ = 19 X