A hammer mill is driven by a High Torque (HT) AC motor. The system is used for 8 hours /day. Input speed is 870 RPM and input power is 25 HP. Nominal output speed is 310 RPM. Design a V-belt drive and specify: (a) (b) (c) (d) (e) the belt size, the sheave sizes, the number of belts,               theactualoutputspeed, the center distance. Show all your calculations.

Q: A 50 Hz pump drive requires a torque of 70 Nm approx. at 1450 rpm approx. for 1 minute followed by 5…

A: To Find : The number of poles, The continuous power rating The required power rating for 200% pull…

Q: n Electrical motor (heavy start) that delivers 53,57 kW at 1440 r/min must be connected to a tary…

A:

Q: A belt drive is to be used for transmitting 3KW from an electric motor whose speed is 1500rpm to a…

A: The reduction of the gearbox or gear ratio is evaluated by dividing the larger gear teeth number by…

Q: Calculation for drive system and rack/spur gear of a crane. System needs to able to climb an incline…

A:

Q: A belt conveyor transports 18 tonnes per hr at 20°. Determine the speed reducer power factor to lift…

A:

Q: a V-belt depends on the rotational speed of the smaller pulley.

A: In belt drive power transmission depends on following factors 1 linear velocity of velt 2 tension of…

Q: A V-belt drive is required from a 10kW, motor to drive an output pulley of 240mm diameter at 500pm…

A: To find:Suitable V-belt and motor pulley diameter for a single belt installation

Q: A ( 20 ) H.P. , ( 960) Ep.m. motor has a mild steel shaft of (4) cm diameter and the extension being…

A: The solution step by step is given below

Q: What is the no of teeth in driven sprocket? Select a suitable roller chain.What is it's label?…

A: Given: P=15 kW Driven speed =1400 rpm Driving speed =350 rpm center distance is nearly 40 times the…

Q: A multiple-disk clutch is to operate in oil and be able to transmit a design overload torque of 800…

A: Given:T = 800 N-mDo = 150 mm = 0.150mDi = 90 mm = 0.09mpmax =1000 kPaf = 0.10To findTotal number of…

Q: An AC motor operating at 870 rpm drives a sheave for a 5V belt with a diameter of 8.9 inches. The…

A:

Q: solve Q a.

A: Given Data⇒V belt driveProblem definition⇒Problem says estimate initial tension for a V belt drive

Q: The ratio of tension on the tight side to that of the slack ride in a flat belt drive is

A: Given, find the ratio of tension on the tight side to that of the slack ride in a flat belt drive

Q: lease show step by step manual solution and diagram for Machine Elements 2 problem below.  .A…

A: Given data: LCD=1100 mmd=600 mmP=40 KWNs=500 rpmαs=1440 ( a)Determine the diameter of driven pulley

Q: To design a gearbox that will allow a motor to lift a 120lbf load 60ft vertically in 30 seconds…

A: A transmission is another name for a gear box. A set of gears and their case, most typically…

Q: (c) Find the smallest number of teeth theoretically required (in order to avoid interference) on a…

A: C) Given: Pressure angle (φ)=22.5°

Q: Figure 1. The maximum extension of spring (ymax = 8.3 mm), the dynamic load varies from 250 N at the…

A:

Q: 112 he Ratio between the Outside and Inside Diameter of the Disk is 100 the coefficient of friction…

A:

Q: Refer to hoist system arrangement as in Figure Q1(b) and specifications details in Table Q1(b).…

A:

Q: What type, size, and a number of classical V-belts is recommended for this system.  The motor is…

A: V-belt pulleys (additionally called vee belt parcels) are gadgets which send power between axles by…

Q: (b) A multiple plate clutch has more number of clutch plates. A typical clutch consist of the…

A:

Q: 3)Design a V – Belt drive to the following specifications Power transmitted = 75kw Speed of driving…

A:

Q: Design a V-belt system to transmit a power of (24) Kw between two shafts at (1200) rpm with a…

A: Write the rated power. Prated=25 kW   Calculate the Design power. Pdesign=PratedSF=251.4=35 kW

Q: ure the maximum life of a belt, the setting up is very important. Discuss the initial tension…

A: given: To ensure the maximum life of a belt, the setting up is very important. Discuss the initial…

Q: rmine the pow

A:

Q: Q1. An open belt drive configuration having 10 pulleys in total, the input and output speeds are 20…

A:

Q: What is the extreme transmission angle values by using maxima and minima condition, of the…

A: Given:-

Q: An A-3 polyamde conveyor belt is to be.dnuen 530mm: Ihe pully shoift which is ya pulley with a…

A:

Q: The spur gear is used to transmit power of 30 kW at velocity of 14 m/sec with service factor of 1.2.…

A: Given Data P=30 kW V=14 m/s Ks=1.2

Q: A belt conveyor transports 18 tonnes per hr at 20°. Determine the speed reducer power factor to lift…

A: Given Datam=18T/hrN=1750rpmS=33.5mV=61m/min

Q: Design a chain drive to run a blower at 600 rpm. the power to the blower is available from a 8kw…

A: Given Blower NB = 600 rpm Motor power = 8 kW Motor NM = 1500 rpm Distance = 800 mm To find Chain…

Q: Pinion 2, which is located on shaft "a", rotates at 1800 rpm, and transmits 75kW to the idler gear 3…

A:

Q: The client requires a single step up spur gearbox to transmit a 10kW power from a shaft rotating at…

A:

Q: Design a helical extension spring to hold the roller follower against the cam as shown in Figure 1.…

A: Given dataMaximum extension of the spring ymax = 8.3mmVariation i dynamic force 250N to 400NDiameter…

Q: 2. Try to design a single reducer with a cylindered worm gear driv Given the rated power of electric…

A: Here, P=7.5 KW i=24 n=1440 rpm

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.