2. A 75 kW induction motor runs at 740 rpm in clockwise direction. A 19 tooth helical pinion with20 degree normal pressure angle, 10 mm normal module and a helix angle of 23 degree is keyed to the motor shaft. Draw a 3-dimensional sketch of the motor shaft and the pinion. Show the forces acting on the pinion and the bearing at A and B. The thrust should be taken out at A All dimensions are in mm A 750 B 200 Z2= 38 Z₁ = 19

2. A 75 kW induction motor runs at 740 rpm in clockwise direction. A 19 tooth helical pinion with20 degree normal pressure angle, 10 mm normal module and a helix angle of 23 degree is keyed to the motor shaft. Draw a 3-dimensional sketch of the motor shaft and the pinion. Show the forces acting on the pinion and the bearing at A and B. The thrust should be taken out at A All dimensions are in mm A 750 B 200 Z2= 38 Z₁ = 19

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A 2hp motor is to drive a food shredder. The motor is projected to run at 1450 rpm and the required speed at the food shredder is 60 rpm. Design a double reduction drive consisting of belt and chain for this application. Please give solution and show drawing if needed
As shown in the figure, 2 lumped masses that are not in the same plane are connected to a shaft between the bearings at A and B. The spindle is rotated counterclockwise with a constant speed of 1450 rpm. Perform the dynamic balancing of this prototype rotor system. -Required corrective masses in the L and R planes from the C axis of rotationIt will be placed at a distance of 50 mm. -The values of the required corrective masses will be found in grams. -The angle positions of the necessary corrective blocks will be written in polar style at the last stage. -For the solution, the "Algebraic Solution" method based on Cartesian components will be used.
Do it
A four-part mechanism like this one, if it is known the length of o2a (link 2) is 5 cm (link 3) is 4 cm (link 3) and the length of the bo4 (link 4) is 5.5 cm (5 in.). At the a point working the p = 50 Newton style with the sustric orientation of the horizontal line is 20⁰, look for styles that are going on and torque on link 4.
A straight tooth spur pinion has a 19 tooth pinion rotating at a speed of 1640 rpm. The driven gear will be rotating at a speed of 480 rpm. If the module of the pinion is 2,5 mm and pressure angle is 25 degree; Evaluate the outer diameter (mm) of the gear.
please help me calculate the velocity ratio
A belt conveyor transports 18 tonnes per hr at 20°. Calculate the height in m to lift the load vertically up sufficient to give 33.5 m inclined belt length. 1750-rpm motor, V-belt drive to helical gear speed reducer. Belt speed, 61 m/min. Discharge over tail pulley. No tripper.
A spur pinion rotating at 20 rad/sec and having 20 teeth transmits 20 kW to a gear wheel. The pressure angle is 20° and module is 20mm. The reaction exerted by the pinion at the centre of thc shaft is
Design machine
PLEASE ANSWER PART 4 and 5 Part 1 Calculate the polar moments of inertia in segments (1) and (2). Answer: J₁ = 13.84 in.⁴ J₂= 1.535 in. ⁴ Part 2 Calculate the internal torques T1 and T2 in shaft segments (1) and (2), respectively. On paper, prepare an internal torque diagram for the compound shaft that shows these internal torques. Use the sign convention presented in Section 6-6. Answer: T₁ = 800 Ib-ft, T₂= -800 Ib-ft. Part 3 Calculate the maximum shear stress in each shaft segment. On paper, prepare a diagram that shows the maximum shear stress in segments (1) and (2) of the shaft. Use the sign convention presented in Section 6-6. Answer: τ₁ = 1560.69 psi, τ₂ = -7817.59 psi Part 4 (PLEASE ANSWER) Determine the rotation angle of B with respect to the support at A. Please Answer: φB= rad. Part 5 (PLEASE ANSWER) Determine the rotation angle of C with respect to the support at A. Please Answer: φC= rad.
PLEASE ANSWER ?? ?Part 1 Calculate the polar moments of inertia in segments (1) and (2). Please Answer: J₁ = in.⁴ J₂= in. ⁴ ?Part 2 Calculate the internal torques T1 and T2 in shaft segments (1) and (2), respectively. On paper, prepare an internal torque diagram for the compound shaft that shows these internal torques. Use the sign convention presented in Section 6-6. Please Answer: T₁ = Ib-ft, T₂= Ib-ft. ?Part 3 Calculate the maximum shear stress in each shaft segment. On paper, prepare a diagram that shows the maximum shear stress in segments (1) and (2) of the shaft. Use the sign convention presented in Section 6-6. Please Answer: τ₁ = psi, τ₂ = psi ?Part 4 Determine the rotation angle of B with respect to the support at A. Please Answer: φB= rad. ?Part 5 Determine the rotation angle of C with respect to the support at A. Please Answer: φC= rad. Thank you so much in advance
A 1" diameter line shaft, which is supported by frictionless pulleys at the ends, carries 2 pulleys. The 10" diameter driver pulley is driven in a counter-clockwise direction, and its belt tensions are 25 lbs and 56 lbs. The 2" diameter driven pulley has one of its belt tensions measured at 30 lbs. Calculate the missing belt tension.