An electric motor running at 970rpm is used to drive a rock crushing machine with a design power of 32 kW. A 33oz ducking weight flat belt drive is proposed with a tension ratio of R = 4 and belt width b = 120 mm. The pitch diameter of the driving pulley (on the motor-end) is 320mm. a) What is the mass per mm width per m length per ply in kg/mm/m/ply? Number (exact value) b) What is the maximum working tension per mm width per ply in N/mm/ply? Number (exact value) c) Calculate the belt velocity in m/s Number (+/-1%)

An electric motor running at 970rpm is used to drive a rock crushing machine with a design power of 32 kW. A 33oz ducking weight flat belt drive is proposed with a tension ratio of R = 4 and belt width b = 120 mm. The pitch diameter of the driving pulley (on the motor-end) is 320mm. a) What is the mass per mm width per m length per ply in kg/mm/m/ply? Number (exact value) b) What is the maximum working tension per mm width per ply in N/mm/ply? Number (exact value) c) Calculate the belt velocity in m/s Number (+/-1%)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A conveyor is used to drive the inertial load of 0.02 kg m² in the required speed range with a brushless DC motor and a gearhead having reduction ratio of 15:1 as shown in the figure below. The belt speed is V=1 m/s and the roller diameter is D=0.1 m. Choose the correct statement. Load Motor Right Angle Gearhead O The moment of inertia of the load referred to the motor shaft is 0.00133 kg m² O The moment of inertia of the load referred to the motor shaft is 0.0133 kg m² O The rotation speed of the motor shaft is 1665 RPM O The rotation speed of the gear shaft is 100 RPM O The rotation speed of the motor shaft is 2865 RPM.
Please only do if you have knowledge and 100% sure and please only handwritten I need or skip
A narrow V-belt (wedge belt) transmits power from an internal combustion engine operating at 700 rpm to the shaft of a dough mixer (medium duty) operating at 50 rpm. The internal combustion engine develops a nominal power of 50 kW and the dough mixer operates for no more than 8 hours per day. Which of the following belts can be used for this application? Hint: First determine the design load by using an appropriate service factor from page F12 in Appendix H in the Design Manual. SPC only SPB or SPC SPA or SPB SPB only
STATİC I need the answer within 1 hour. Thanks Rod AB is secured from point B with a cable and from point A with a smooth, up and down movable collar. Calculate the tensile strength generated in the BC cable. ? = {−??} N direction is -z a(m)=15.75 , b(m)=13.5 , c(m)=8.55 d(m)=3.75 F(N)=61.5
A 2hp motor is to drive a food shredder. The motor is projected to run at 1450 rpm and the required speed at the food shredder is 60 rpm. Design a double reduction drive consisting of belt and chain for this application. Please give solution and show drawing if needed
A winch drum of diameter 161 mm turning at 12pm lifts a load of 7.5kN. What is the winch output power?
i need the answer quickly
5. In the mechanism shown in the figure, a-150mm,b-155mm,c%3D160mm,d%3D100mm, e=350mm. Analysis whether the mechanism has the quick-return motion when AB acts as the driving link and slider E acts as the driven link (If it has, redraw a figure to find the coefficient of travel speed variation K)? Is there a change if CD acts as the driving link? Explain that using the graphical method. Bo e E D
A mini motorcycle is driven by a combustion engine with mechanical transmission. The 12Hp motor spins at a speed of 1150 rpm. The motorcycle runs at a linear speed of 45 km/h on 12-inch wheels. Preliminary center to center distance is 13”. This type of motorcycle requires two strands (conical double sleeve assembly) and is subjected to hard shocks. Can I get a detailed explanation for Choice of chain and sprocket. (Standard part number, see catalog) https://pdf.directindustry.com/pdf/martin-sprocket-gear/general-catalog/9091-246439.html
Explain the Schematic Diagram in this problem. (tanginamo1 is the problem) and (tanginamo2 is the schematic diagram) Provide a reasonable explanation, thank you!
FINAL QUIZ IN PME 412 MACHINE DESIGN 1 PROBLEM: FOR HIBISCUS AND ROSE GROUPS 1. A helical spring must be capable of exerting a force of 600 N after being released 10 mm from its most highly compressed position. Wire of 6 mm diameter is used; the spring index is equal to 6. The loading is static. The maximum stress is 400 MPa. Find the required number of active coils.
The picture shows the rear swivel axle bearing design of a 4-wheel wagon. It is known that the speed of the wagon wheels is n = 37 rpm. The total radial load carried by the wagon is given as Fr= 16060 Newtons. In addition, due to road conditions, Fa axial load is applied to the wagon. If the axial load on the A bearing is 10% of the radial (vertical) load on this bearing, calculate the dynamic load number (C) of the bearing in the A bearing in Newtons for 18616 hours of life. fo*Fa/Co = 0.345 Pi=3.14