Match the following. Prompts Breather Answers 2 Strainer 3 Regulator Select match Filters ambient air before entering the compressor. Select match Expels air when excess pressure is sensed. Select match Sets the operating pressure of the pneumatic system. Moisture Separator Select match 5 Aftercooler Select match 6 Air Heater Select match 7 Silencer Removes moisture from the compressed air. Works in conjunction with the strainer. Provides manual control of air flow. Used to reduce pulsations and also can be used as an emergency backup supply. Select match Used to prevent freezing of exhaust ports in cold environments 8 Shut off/on valve Select match 9 PRV Select match 10) Accumulator Select match Sintered brass usually placed on exhaust ports. Removes contaminants from the pressurized air. A cold-water heat exchanger used to condense moisture from the air.

Match the following. Prompts Breather Answers 2 Strainer 3 Regulator Select match Filters ambient air before entering the compressor. Select match Expels air when excess pressure is sensed. Select match Sets the operating pressure of the pneumatic system. Moisture Separator Select match 5 Aftercooler Select match 6 Air Heater Select match 7 Silencer Removes moisture from the compressed air. Works in conjunction with the strainer. Provides manual control of air flow. Used to reduce pulsations and also can be used as an emergency backup supply. Select match Used to prevent freezing of exhaust ports in cold environments 8 Shut off/on valve Select match 9 PRV Select match 10) Accumulator Select match Sintered brass usually placed on exhaust ports. Removes contaminants from the pressurized air. A cold-water heat exchanger used to condense moisture from the air.

Automotive Technology: A Systems Approach (MindTap Course List)

6th Edition

ISBN:9781133612315

Author:Jack Erjavec, Rob Thompson

Publisher:Jack Erjavec, Rob Thompson

Chapter55: Air-conditioning Diagnosis And Service

Section: Chapter Questions

Problem 8ASRQ: While discussing an inoperative blend air door: Technician A says that to check the proper...

See similar textbooks

Similar questions

--------Q.1// A conference room is to be air conditioned for comfort conditions of (25oC) DBT and (50% RH). The outdoor air conditions are (35oC DBT) and (28oC WBT). The sensible and latent heat are (43200 kJ/hr) and (36000 kJ/hr) respectively. The return air from the conference room is mixed with outdoor air before entering the cooling coil as shown in the Figure below. In addition, the return air from the (conference room) is mixed with cooling air (after cooling coil) see Figure below, where cooling coil by bass factor (BPF = 0.1) and (ADP =10oC). Theair is reheated to (21oC DBT) before supplying to room.Note: point 6 not equal to point 1.Determine:1 – Conditions at point 3 (DBT3, WBT3, RH3, h3).2 – Conditions at point 4 (DBT4, WBT4, RH4, h4).3 – Conditions at point 5 (DBT5, WBT5, RH5, h5).4 – Conditions at point 6 (WBT6, RH6, h6).5 – The total quantity of air supplied to conference room (kg/sec). 6 – Capacity of reheated coil (kJ/kg).7 – Sensible heat factor SHF.8 – Capacity of…
 Discuss the difference between an air cooled vehicle engine and a liquid cooled engine Discuss the reason to use “Engine Coolants” in engine cooling system. Explain vividly about the functions of Thermostat valve and pressure cap. Discuss the main functions of the lubricating system of an engine Discuss the types of lubricating systems available. Discuss about the Lubricant Classification Discuss how to check lubricant quality of an automobile.
What pumping capacity (Ls) is required for the vacuum pump of a GC-MS if the carrier gas exits the GC column with a flowrate of t mimin at a temperature of 250°C at 1 atmosphere of pressure but the mass spectrometer source is at a temperature of 250°C and pressure of 1x10 atm. A. 174 B. 167 O C. 224 O D. 216 Reset Selection
Explain why the outside air damper is typically never completely closed, even when the outside air conditions are not adequate to provide free-cooling.
State the main advantage that a discus compressor's valve plate design has over a conventional piston-type compressor.
When the car engine is cold, the main cooling cycle is blocked to allow good oil filtration. O increase the engine temperature up O to the optimum engine temperature. easier to be derived. O be better for transmission system. O replace radiator cap. O
Contrast the major differences between these three different mechanical ventilators: Puritan Bennett 980 Series Ventilator, Maquet Servo i, and Nellcor puritan bennett 840 Ventilator System?
Complete the schematic below to provide for the following: 1. Cylinders extend and retract together. The cylinders extend when the valve lever is pulled ouat and retract when the lever is pushed in. 2. Provide independently adjustable meter-in flow control for extend. The flow control used to extend Cyl #1 should be labeled "FC1". The flow control used to extend Cyl #2 should be labeled "FC2". 3. Provide independently adjustable meter-out flow control for extend. retract The flow control used to retract Cyl #1 should be labeled "FC3". The flow control used to retract Cyl #2 should be labeled "FC4". CYL1 CYL #2 "AUHVA
Which of the following statement(s) about steam calorimeters is/are correct? O The ideal degrees of superheat of steam passing through throttling calorimeter is 5.5°C O Typical condition of steam entering a calorimeter is wet-vapor mixture and superheated when exiting O Electrical calorimeter operates approximately as barrel calorimeter with modifications in some parts. O If a throttling calorimeter is insufficient, there is a need to measure the pressure and temperature of steam passing through it. O For a separating calorimeter. series of obstacles are found within the separating charmber which separate liquid particles from vapor. O Actual quality of the steam is equal to the computed value of dryness fraction, neglecting lossies O For separating and throttling calorimeter, the quality 2 is greater or higher than quality 1.
While discussing an inoperative blend air door: Technician A says that to check the proper functioning of the ductwork, move the temperature control lever to see if any change at the doors occurs. If it does not, shut off the air conditioner and turn on the heater. Move the temperature control arm again to see if any change occurs. If not, check the cable and the flap door connected to the temperature control lever. Technician B says that in some cases you can reach under the dash to reconnect the cable or free a stuck flap. Who is right? Technician A only Technician B only Both A and B Neither A nor B
Explain how the oil separator, oil reservoir, pressure differential valve, and oil-level regulators work together tomaintain the correct oil level in parallel compressors.
About hydraulic for aircraft. How to know the bad condition of the moisture separator component and what’s the effect of it to the system?