Solve for A and B. P=400 lbs. 0=30° P 45° B www Drawing not to scale. Use given angles. Magnitude of Axial Force in Member A Magnitude of Axial Force in Member B Is Member A in Tension or Compression? Is Member B in Tension or Compression? 869 lbs 636 lbs Member A is in Compression + Member B is in Compression +

Solve for A and B. P=400 lbs. 0=30° P 45° B www Drawing not to scale. Use given angles. Magnitude of Axial Force in Member A Magnitude of Axial Force in Member B Is Member A in Tension or Compression? Is Member B in Tension or Compression? 869 lbs 636 lbs Member A is in Compression + Member B is in Compression +

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

FREE-BODY DIAGRAM EXERCISES 3/A In each of the five following examples, the body to be isolated is shown in the left-hand diagram, and an in- complete free-body diagram (FBD) of the isolated body is shown on the right. Add whatever forces are nec- essary in each case to form a complete free-body dia- gram. The weights of the bodies are negligible unless otherwise indicated. Dimensions and numerical values are omitted for simplicity. Body Incomplete FBD 1. Bell crank supporting mass m with pin support at A. mg m Flexible cable A Pull P P. 2. Control lever applying torque to shaft at 0. Fo 3. Boom OA, of negligible mass compared with mass m. Boom hinged at O and supported by hoisting cable at B. B m mg 4. Uniform crate of mass m leaning against smooth vertical wall and supported on a rough horizontal surface. A mg B B 5. Loaded bracket supported by pin connection at A and fixed pin in smooth slot at B. Load L Figure 3/A Page5
P1=215 N P2=325 N P3=150 N L1=3m L2=4m 1. Draw a "free body diagram". The diagram should be for members BE, BF, CF, and DF to help solve. 2. What is the force on members CF, BF, BE? Is each of these members having tension or compression?
2 m 2 m 2 m 2 m D F G H 2 m 1 m C 0.5 m 2 m F B M 2 m Determine the forces in members DE and DL. State if each forces are compression or tension. If the force is 10 kN. Input DE force member and four decimal values on the blank indicate the stress (Tension or Compression.) e.g: 829.91 N-T
A puck weighs 8 lb and rests on the center of the frictionless surface of the ramp supported in equilibrium by ropes AC and BC. Determine the normal force the ramp exerts on the puck as well as the tension in each of the two ropes. g Variable Value Values for dimensions on the figure are given in the following table. Note the figure may not be to scale. a b C d e f g9 36.0 in 45.0 in 13.5 in 27.7 in 45.0 in 18.0 in 35.0 in B The normal force acting on the puck is pounds The tension in rope AC is The tension in rope BC is C pounds pounds
Determine the force in each member of the loaded truss. The forces are positive if in tension, negative if in compression. kys Part 1 B 3.1 m AD 50° CD Answers: AD = The Free-Body diagram for joint D is drawn assuming that all internal forces are in tension. Solve for the forces in AD and CD. The forces are positive if in tension, negative if in compression. 50 CD = i 6.2 m 50 D 50° 3600 N 3600 N N N
Frames & Machines The truck shown is used to deliver food to aircraft. The elevated unit weighs 2000 Ib with center of gravity at G. 1- Derive the expression for the force in the hydraulic cylinder AB as a function of 0 (the angle that member FD makes with the horizontal). 2- Plot the force over the range 0° < 0 < 45° and discuss your observations. Note: | would suggest that you first solve the problem based on the position (angle) shown. You will need to determine the length of members FD and FB before solving the problem for arbitrary 0. Note that the location of the roller at D and hence the force reactions will change as 0 varies. 40" 17" 57" C 54" E 54" H AB
P3: Determine the magnitude of the axial forces in the given truss below. Ure method of joints and check your answer by solving for the magnitude of the axial forces of DF, FC and CE using Method of Sections. 20 20 20 kNI kNI kN 5 m 80 kN ACTE G. 3 m 3 m 3 m 3 m Prenarad hM
The jaws and bolts of the wood clamp in Fig- are parallel. The bolts pass through swivel mounts so that no moments act on them. The clamp exerts forces of 300 N on each side of the board. Treat the forces on the boards as uniformly distributed over the contact areas and determine the forces in each of the bolts. Show on a sketch all forces acting on the upper jaw of the clamp. D 100 mm 150 mm B H00 mm75 mm-100 mm-
Show your complete solution including the diagrams and box your final answers with their appropriate unit. Use up to 4 decimal places. Moment of the single 100 lb forcei. When the tail of the force is at itsoriginal position using ? = ? × ?ii. If you slide the force so that its tailis at the y-axis using ? =(±)|?||?|iii. If you slide the force so that its tailis at x-axis using ? = (±)|?||?|
Given the figure determine the bar force at BD and AB
Question 16 10 20 kN 20 kN 20 kN 3m -40 kN 3m D. 3 m 40 kN- 3 m 6 m Determine the force in member CE. If the force is in compression, write your answer as negative. If the force is in tension, just input the value
Question-3 Find the magnitude and nature of the forces in all the members of the given truss. Figure: 3 20 kN 12 kN 2 m 2 m 2 m 3 m 02 Өз E G Figure: 3