Knowing the tension in cable BD is 1300 N, the shown system can be simplified to the following force-couple system at B: F = (50 i-1950 j) N C=397500 N·mm Another equivalent force-couple system is expressed as simply the resultant force F placed at a certain distance d between points A and B as shown on the figure (measured from B). What is the distance d that gives an equivalent system? 750 N 150 mm 250 mm -500 mm A 450 N 400 mm B C D 600 mm

Knowing the tension in cable BD is 1300 N, the shown system can be simplified to the following force-couple system at B: F = (50 i-1950 j) N C=397500 N·mm Another equivalent force-couple system is expressed as simply the resultant force F placed at a certain distance d between points A and B as shown on the figure (measured from B). What is the distance d that gives an equivalent system? 750 N 150 mm 250 mm -500 mm A 450 N 400 mm B C D 600 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Difficult Problem: If magnitude of MA is 1200 kN – m and the distance between A and B is 3 m, what is the force FB and distance d so that the system shown at the right is equivalent to a force-couple system acting at point D, where the horizontal component of this force is R = 112 kN to the right and the corresponding couple is 635 counterclockwise. 60 kN 30 50 kN 2 m MA 60° 15° 200 kN m 100 kN 4 m Fs 2 m 200 kN 30 60 kN -3 m
Q6: For the force-couple system shown in figure (6); determine an eguivalentcouple (M) and resultant force CR) at point (A). 1.5M 2KN 50ON.m osm 70° 015M 1-2 KN Fig (6)
A 30 N force acts on the end of the 3 m lever as shown. The moment of the force about '0' is : 20° 30 N 3 m 50 A:- 30.8 N-m - (Correct Alternative) B: 30.8 N-m C:- 12.72 N-m D: 12.72 N-m
200 lb 0 400 lb 3 ft 4 ft (a) 300 lb 2 ft 3 ft y For the loaded plate shown, four parallel forces are applied Three of the 4 forces are shown. The fourth force P and its line of action are unknown. The resultant of this force-couple system is only represented by the couple vector CR=-1100i + 1500j lb.ft. Determine the force P and its line of action. 1. Solve this problem algebraically by hand 2. Write a code to solve it arbitrarily. 3. Use part 2 to verify part 1. 4. In your submission include both just the code plus the "run" version of the code to show the results for P
Given the picture below, if If L=80.0 N and A=60.0N, what is the fource couple at C equivalent to the 2 forces ?
Q2: Determine the resultant couple moment of the three couples acting on the plate in figure below. sibi F1=24 N F3=45 N 4 ft F2= 78 N 5 ft 3 't
for the following system, assume tension in cable BC=10 kN, and in BD= 8 kN to answer the followings 1) Express force in each cable in cartesian coordinate system 2) Calculate moment due to both cables and force 4kN about point A 3) Calculate moment due to both cables and force along line BC B. 5 m T1 Ta 4 kN 5 m 4 m 12 m 5 m -- 4 m
Five forces and a couple act on the plate shown in the figure . - Find the resultant ( R ) Of the four forces , and its angle (e). - Locate it with respect to point ( O). - Show where the resultant cuts both the x - and y- axes. 400KN 7m 1o0 KN 6 m lom 800 KN-m V150 KN 18m 7200KN 100 KN L 8 m
ENGINEERING MECHANICS STATICS Example: Determine the resultant couple moment of the three couples acting on the plate in the figure. F = 200 lb %3D F3 = 300 lb -d = 4 ft- F2 = 450 lb A %3D d3 = 5 ft d2 = 3 ft %3D F = 450 lb B. %3D F = 200 lb F3 = 300 lb Solution: 2och nair of counle foro
For the bent pipe shown in the figure, it is sought to replace the system of three forces with a single equivalent resultant force R. Find the distance d (in metres) from point O to the point on the x-axis through which the line of action of R passes. a = 379 N, b= 146 N 0.25 m 50 N 0.25 m a b 0.25 m 0.2 m x
Given the Position vector Ř = -i+ 6j+ 3k (m) and the Force vector F = -i – 3j + 8k (kN) Determine R. F Answer:
It is desired to remove the spike from the timber by appying force along its horizontal axis. An obstruction "A" prevents direct acess, so that two forces, one 400LB and the other "P" are applied by cables as shown. Here we want to investigate the effects of the distance between the spike adn the obstruction on the two forces so replace 8" by "d" in the figure. Determine the magnitude of "P" necessary to insure a resultant "T" directed along the spike. Please show all work and FBD thank you!