Make Diagram For the Below Details 1. Pump (12v 110psi max pressure) 2. Battery (12V 8Ah) 3. On/off switch (remotely controlled) (relay) 4. Adjustable Pressure Switch 5. Charging Port Explanation:: It is a sprayer, it pumps water with varying force/strenght(where the valve like thingy comes in). it also has 2 swithches, 1 where you press it and 1 where there is a remote(this the the one inside a box in the pictures attached to this Post.)

Make Diagram For the Below Details 1. Pump (12v 110psi max pressure) 2. Battery (12V 8Ah) 3. On/off switch (remotely controlled) (relay) 4. Adjustable Pressure Switch 5. Charging Port Explanation:: It is a sprayer, it pumps water with varying force/strenght(where the valve like thingy comes in). it also has 2 swithches, 1 where you press it and 1 where there is a remote(this the the one inside a box in the pictures attached to this Post.)

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter4: Symbols

Section: Chapter Questions

Problem 8SQ: The symbol shown is a a. normally open pressure switch. b. normally open flow switch. c. normally...

See similar textbooks

Similar questions

Could you slove this dc electrical circuit
A practical switch is operating at a switching frequency of 100 kHz and a 0.5 duty cycle. The switch is initially on (the first half cycle). The switch has the following parameters: Von = 0.1 V Volt 80 V Ion - 100 A 10.1 A ton = 0 Loft O Ldelay O a) Draw clear voltage and current waveforms for one switching cycle with all values shown (times, voltages, currents, etc.). b) Find the average power loss in one switching cycle.
1. What happened if the DC voltage in the clamping circuit is replaced by an a.c source?
Why PMMC Voltmeters can not be used to measure higher voltages directly? a. because the size of the coils will raise b. because the coils will not be present at all c. because of the lesser current ratings. d. because of the lesser size problems
a. Describe the action of the circuit shown in the figure-1 below SPEAKER Vin RE
PMMC type meter has a full scale deflection of 10 mA. The resistance of the coil is 30 ohm So, (1) Value of shunt for ammeter of 50 A range and (2) Find the value of series resistance required for the range up to 500 V.
Electric Powers System for Nonelectrical Professional can you explain the operation and need for voltage regulators and tap changers
Carefully define or explain the following terms in your own words (give units where appropriate): a. Electrical current. b. Voltage. c. An open switch. d. A closed switch. e. Direct current. f. Alternating current.
3. Explain how/why the pull-up resistor conducts and under which conditions
Module 10 Section Review 3.0.0.png Additional Resources Electronics Fundamentals: Circuits, Devices, and Applications, Principles of Electric Circuits, Thomas L. Floyd. New York: Prent 3.0.0 Section Review 1. The letter designation SL on an electrical draw- ing indicates a 4. A a. a. limit switch b. low-voltage switch c. load switch d. light switch b. C. d. 2. Existing power lines on an electrical site plan may be indicated by the letter 5. In t safe a. E b. I a. b. 2 С. Р d. V C. 2 d. 2: 3. The specific types of luminaires required in an installation can be found on the a. power plan b. electrical site plan c. schematic diagram d. lighting fixture schedule P Search for anything
what are charging and discharging time of this circuit.
26 CHAPTER 2 Symbols and Schematic Diagrams REVIEW QUESTIONS 7. Referring to the circuit in Figure 2-22, should the float switch be connected as a normally open or normally closed switch? 8. Referring to the circuit in Figure 2-22, what circuit component controls the actions of the two CR contacts? 1. The symbol shown is a a. polarized capacitor. b. normally closed switch. c. normally open, held closed switch. d. normally open contact. 2. The symbol shown is a a. normally closed float switch. b. normally open, held closed float switch. C. normally open float switch. d. normally closed, held open float switch. 9. Why is a circle most often used to represent a coil in a motor control schematic? 10. When reading a schematic diagram, are the control components shown as they should be when the machine is turned off or de-en- 3. The symbol shown is a(n) a. iron core transformer. ergized, or are they shown as they should be when the machine is in operation? b. auto transformer. c. current…