Figure P1.39 VPS = 1.2 V R1 = 50 ΚΩ ww R₁₂ = 30 ΚΩ ww ID↓ + ✓ VD Questions to be addressed: (1) Is the diode forward biased or reverse biased? (Qualitative analysis will be sufficient (2) If forward biased, how much is the diode current? (Quantitative analysis required) (3) If reverse biased, how much is the reverse voltage across the diode? (Quantitative analysis required)

Figure P1.39 VPS = 1.2 V R1 = 50 ΚΩ ww R₁₂ = 30 ΚΩ ww ID↓ + ✓ VD Questions to be addressed: (1) Is the diode forward biased or reverse biased? (Qualitative analysis will be sufficient (2) If forward biased, how much is the diode current? (Quantitative analysis required) (3) If reverse biased, how much is the reverse voltage across the diode? (Quantitative analysis required)

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

What is the difference between a diode and rectifier?
What is CEMF?
The diode from the following characteristic curve in Figure 1 was changed to zenerdiode. Determine: the function of zener diode in reverse biased. Briefly explain the differencebetween conventional diode and zener diode.
Draw the input waveform and output waveform for the circuit given below with proper values marked in the figure. Assume D1 as germanium and D2 as silicon diodes. Input Vpp%3D20V, V1=3 V and V2=10 V. R D2 D1 Vin Vout V1 V2 Maximum voltage of output waveform Minimum voltage of output waveform Ps
3) With reference to the illustration given below, with detailed explanation discuss about the reverse recovery time and its significance. Current through diode I before reversed Current through diode after reverse biased biased Reverse recovery K time rr Time rm = Reverse maximum Irm Slow Recovery current
Determine the biasing of silicon diode in figure A shown below and draw equivalent circuit based on biasing.
Determine the output waveform for the network of Figure. bellow and calculate the output dc level and the required PIV of each diode.? 10 V 2 kQ T t 2 2 k2 2 kN
When a conventional Silicon diode is reversed-biased with a voltage high enough such that there is a very large current present, the voltage value this occurs at is referred to as the: a) Breakdown voltage b) Breakup voltage c) Hammer voltage d) Roller voltage O b O d O c a o o o o
1. Draw the output voltage waveform for each circuit in Figure below and include the voltage values. N +5V +50V Vin R Va R o 0% Y 9 33k 5 Vo -5V -50v I I (@ () a. Whatis the peak inverse voltage across each diode in Figure above? b. What is the peak forward current through each diode in Figure above?
2.Sketch the waveforms for the load current and load voltage for the circuit show in Figure 2. Show the peak values. Use the offset diode model in your calculations. Input voltage source could be represented as a sine waveform, given as Vin=20sin(wt +30), and RL = 20 S Figure 2 www R₁ Vout
Question-1: Consider the circuit in Figure below. 1. What type of circuit is this? 2. What is the total peak secondary voltage? B. Find the peak voltage across each half of the secondary. 4. Sketch the output voltage waveform across R1. 5. Sketch the voltage through D1? 6. What is the PIV for each diode? 120 V rms D2
There is a small amount of current across the barrier of a reverse-biased diode. This current is called Choose correct answer A) reverse leakage current B) reverse breakdown current c) forward-bias current D) conventional current.