It is required to design full-wave rectifier circuits. Consider the rectifier circuits shown in figures (a) center-tapped rectifier, (b) bridge rectifier. Assume the input voltage is from 120V(rms), 60HZ ac source. The desired peak output voltage vo is 10V. A conducting diode has a voltage drop of 0.7V. In each case, (i) Determine the required turns ratio of the transformer; (ii) Determine the required peak inverse voltage (PIV) of the diodes. D. Center tap line line voltage R voltage

It is required to design full-wave rectifier circuits. Consider the rectifier circuits shown in figures (a) center-tapped rectifier, (b) bridge rectifier. Assume the input voltage is from 120V(rms), 60HZ ac source. The desired peak output voltage vo is 10V. A conducting diode has a voltage drop of 0.7V. In each case, (i) Determine the required turns ratio of the transformer; (ii) Determine the required peak inverse voltage (PIV) of the diodes. D. Center tap line line voltage R voltage

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A single phase – half wave controlled rectifier with freewheeling diode is supplying a load consisting series connected a resistor and an inductance from a 70.7V (RMS), 50HZ sinusoidal AC source. The firing delay of the thyristor is 90° and the load values are R=10Q, L=0.1 H. Define the load current expression and draw the load current by calculating for first two periods. And calculate the average values of the load voltage and current.
Consider the half-wave rectifier shown in the figure below. Let vs be a sinusoidal with 10V peak amplitude with frequency of 60Hz and let R = 1000 ohms. Use the contant voltage-drop diode model with VD = 0.7 V.
S-2) a) On the bridge type full wave rectifier circuit given in the figure Plot the current paths for each of the +/- alternans. b) The waveform of the Vç output voltage is given in the graphs on the side. Draw it in the blank and calculate the peak value and indicate it in the graph. c) Calculate the effective value of the output voltage. (Vç (eff) =… ..?). Note: Diodes are not ideal. VD = 0.7V.
Determine the voltage across the diode, the output voltage, and the current in the resistor in the figure below. Plot these waveforms with proper ac cycle phase alignment. 1SR154-400 is a silicon rectifier 1 ampere diode. Indicate the peak values as per calculation.
For the circuit shown below, compute the maximum current through each resistor when terminal A is a) positive and, b) negative. Assume the diodes are ideal. (Will we convert to the RMS value to it's actual value?)
.Draw a full-wave rectifier circuit (using a diode bridge) and predict the output voltage signal when the input is a sinusoidal signal with amplitude 10 V (p p). Use the previous full wave rectifier to create a peak detector with a 2 V ripple.
Q4/: A full-wave bridge rectifier at (2:3) transformer with a [77 sin(2n x 100 x 10³t)] rms input signal has a load resistor of 3.3k2. Draw the rectifier circuit and: 1. Sketch and determine effective waveform voltage (VL-P) at the load. 2. Determine the required PIV rating of the diode. 3. What input frequency and output frequency ? 4. What is the de voltage available at the load? 5. Explain who could filtering output signal. 6. Draw circuit that give opposite out waveform. 7. Why connect circuit in this form.
Write the following for a Semiconverter rectifier with RL load: a) Draw the circuit diagram, supply voltage and the output voltage waveform. b) Explain why there is no negative output voltage even without freewheeling diode. c) Derive the expression for average output voltage.
A bridge rectifier circuit has secondary voltage of 12 V Assume secondary resistance and diode forward resistance to be negligible. Load resistance is 100(ohm.) Calculate peak load current, DC load current, rms current and across each diode.
A half-wave recitifier is connected to a 50V AC source. If the load resistance is 100 ohms, find: 1) Max load voltage 2) Average load voltage 3) Max load current 4) Average load current 5) RMS load current 6) PIV rating for diode ...
Give a design for a pn diode voltage reference source that outputs 5 volts DC from a 12-volt source. Assume that the diodes have an emission coefficient of 1.2 and a reverse saturation current of 300 pA. Weight the alternatives of using a stack of 7 versus 8 diodes. Be sure to specify the resistance and power rating of the series resistor.
A three-phase half wave rectifier has a supply of 150V/phase. Determine the mean load voltage and the required diode rating, assuming the load current is level at 25A. Assume each diode has a volt-drop of 0.7V.