It is observed that the helical pressure spring with an arc index of 8 makes a 68 mm sehim as a result of exposure to an axial load of 35 kN. Find the broadcast wire diameter, the average winding circle diameter and the number of active winding since the slip module is known to be 80 GPa, the maximum shear stress value is 435 MPa.

It is observed that the helical pressure spring with an arc index of 8 makes a 68 mm sehim as a result of exposure to an axial load of 35 kN. Find the broadcast wire diameter, the average winding circle diameter and the number of active winding since the slip module is known to be 80 GPa, the maximum shear stress value is 435 MPa.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.5.31P

See similar textbooks

Similar questions

A small lab scale has a rigid L-shaped frame ABC consisting of a horizontal arm AB (length b = 10 in.) and a vertical arm BC (length c = 7 in.) pivoted al point B. The pivot is attached to the outer frame BCD that stands on a laboratory bench. The position of the pointer al C is controlled by a spring, Jt = 5 lb/in., that is attached to a threaded rod. The pitch of the threads is p = 1/16 in. Under application of load W, 12 revolutions of the nut are required to bring the pointer back to the mark. Calculate the weight W.
A small lab scale has a rigid L-shaped frame ABC consisting of a horizontal aim AB (length b = 30 cm) and a vertical arm BC (length c = 20 cm) pivoted at point B. The pivot is attached to the outer frame BCD that stands on a laboratory bench. The position of the pointer at C is controlled by two parallel springs, each having a spring constant k = 3650 N/m. that are attached to a threaded rod. The pitch of the threads is p = 1.5 mm. If the weight is 65 N. how many revolutions of the nut are required to bring the pointer back to the mark?
A load of 2 kN is dropped axially on a close coiled helical spring, from a height of 250 mm. The spring has 20 effective turns, and it is made of 25 mm diameter wire. The spring index is 8. Find the maximum shear stress induced in the spring and the amount of compression produced. The modulus of rigidity for the material of the spring wire is 84 kN/mm?.
Design a helical compression spring to be used in a cam and follower mechanism made of oil tempered carbon steel, is subjected to a load which varies from 416 N to 970 N. The spring index is 6.2 and the design factor of safety is 1.25. If the yield stress in shear is 770 MPa and endurance stress in shear is 350 MPa,find: 1. Size of the spring wire, 2. Diameters of the spring, 3. Number of turns of the spring, and 4. Free length of the spring. The compression of the spring at the maximum load is 30 mm. The modulus of rigidity for the spring material may be taken as 80 kN/mm2.
A helical compression spring has a scale of 500 lb/in., an outside diameter of 2.75 in, a free length of 8 inches and with squared and ground ends. The load is 1,000 lbs and the working stress on the wire material is 65000 psi. If the Wahl factor of 1.25 is to be used, calculate the following: A. The standard wire diameter B. The number of active coil if G = 10 800 000 psi C. The solid height D. The stress at solid height
A spring made from music wire ASTM 228 steel has the following data:Free length=1.75” Outside diameter=0.561”Wire diameter=0.055” Applied load= 14 lbEnds=square and ground both ends hingedNumber of coils=10 G=11.85 x 106psi E= 30 Mpsi Findspring rate, force at solid length,check for buckling,coil clearance and hole diameter
A helical compression spring is to be used for a maximum load of 1.5 kN using the spring index of 8. The maximum permissible shear stress for the spring wire is 400 MPa. Which of the following is the wire diameter of the spring to be used?
PROBLEM:1 A gas engine valve spring is to have a mean diameter of 55 mm. The maximum load it will have to sustain is 584 N with a corresponding deflection of 7.18 mm. The spring is to be made of tempered wire. Since the material is to be subjected to repeated loading and fatigue must be considered a low working stress of 650 N/mm? will be used. Find the size for wire and number of coils used. Take modulus of rigidity as 0.84 x 105 N/mm? .Assume the spring coil is squared and ground. Take shear stress Concentration factor as 1.15.
Design a helical spring to be used in spring balance with a wire diameter of 6mm and the outside diameter should be limited to 66mm. if the permissible shear stress of the spring material is 325 N/mm? and the Modulus of rigidity is 85kN/mm?. a) Compute the deflection of spring per active turn and the axial load on the spring considering the effect of curvature, take Wahl's factor as Kw= 1.1 b) Calculate the value of axial load neglecting the effect of stress factor. **Note: Please upload your handwritten working/solution to the link provided. The value of Mean diameter of the spring in mm . The Spring Index is. Shear stress factor, neglecting curvature effect . Deflection per active turn in mm Axial Load W in N .. Axial Load W in N. considering effect of curvature .
Design a helical compression spring to be used in a cam and follower mechanism made of oil tempered carbon steel, to sustain a load, which varies from 400 N to 980 N. The spring index is 6.8 and the design factor of safety is 1.25. If the yield stress in shear is 770 MPa and endurance stress in shear is 350 MPa, find: 4. Free length of the spring. 5. Ks= shear factor 6. whals factor The compression of the spring at the maximum load is 30 mm. The modulus of rigidity for the spring material may be taken as 80 kN/mm-.
A helical spring with a load range of from 450 N to 800 N from valve-closed to valve-open conditions is used to close the valve of a spring-set relief valve having a lift of 10 mm. Assuming the spring wire to be of chrome vanadium steel, the spring is rendering average service, determine the diameter of the wire if the spring index is 7 and Sg - 420 MPa. Use G=83GPA. Select one: O a. 2.4-mm wire O b. 5-mm wire O c. 6-mm wire O d. 7-mm wire
Q2: The extension spring shown in the figure has full-twisted loop ends. The material is AISI 1040Q&T 400FO wire. The spring has 82 coils and is close-wound with a preload of 18 Ibf. (a) Find the closed length of the spring.(b) Find the torsional stress in the spring corresponding to the preload.(c) Estimate the spring rate. (d) What load would cause permanent deformation?(e) What is the spring deflection corresponding ?to the load found in part d 0.162 in in R in R. نفس الشي e 5:33