Design a helical compression spring to be used in a cam and follower mechanism made of oil tempered carbon steel, to sustain a load, which varies from 424 N to 990 N. The spring index is 6.2 and the design factor of safety is 1.25. If the yield stress in shear is 770 MPa and endurance stress in shear is 350 MPa, find: 1. Size of the spring wire, 2. Diameters of the spring, 3. Number of turns of the spring, and 4. Free length of the spring. The compression of the spring at the maximum load is 30 mm. The modulus of rigidity for the spring material may be taken as 80 kN/mm?.

Design a helical compression spring to be used in a cam and follower mechanism made of oil tempered carbon steel, to sustain a load, which varies from 424 N to 990 N. The spring index is 6.2 and the design factor of safety is 1.25. If the yield stress in shear is 770 MPa and endurance stress in shear is 350 MPa, find: 1. Size of the spring wire, 2. Diameters of the spring, 3. Number of turns of the spring, and 4. Free length of the spring. The compression of the spring at the maximum load is 30 mm. The modulus of rigidity for the spring material may be taken as 80 kN/mm?.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.3.2P

See similar textbooks

Similar questions

Design a helical compression spring to be used in a cam and follower mechanism made of oil tempered carbon steel, to sustain a load, which varies from 400 N to 980 N. The spring index is 6.8 and the design factor of safety is 1.25. If the yield stress in shear is 770 MPa and endurance stress in shear is 350 MPa, find: 4. Free length of the spring. 5. Ks= shear factor 6. whals factor The compression of the spring at the maximum load is 30 mm. The modulus of rigidity for the spring material may be taken as 80 kN/mm-.
Design a helical compression spring to be used in a cam and follower mechanism made of oil tempered carbon steel, is subjected to a load which varies from 416 N to 970 N. The spring index is 6.2 and the design factor of safety is 1.25. If the yield stress in shear is 770 MPa and endurance stress in shear is 350 MPa,find: 1. Size of the spring wire, 2. Diameters of the spring, 3. Number of turns of the spring, and 4. Free length of the spring. The compression of the spring at the maximum load is 30 mm. The modulus of rigidity for the spring material may be taken as 80 kN/mm2.
Design a helical compression spring to be used in a cam and follower mechanism made of oil tempered carbon steel, to sustain a load, which varies from 400 N to 980 N. The spring index is 6.8 and the design factor of safety is 1.25. If the yield stress in shear is 770 MPa and endurance stress in shear is 350 MPa, find: 1. Size of the spring wire, 2. Diameters of the spring, 3. Number of turns of the spring, and The compression of the spring at the maximum load is 30 mm. The modulus of rigidity for the spring material may be taken as 80 kN/mm. I
Design a helical compression spring to be used in a cam and follower mechanism made of oil tempered carbon steel, to sustain a load, which varies from 400 N to 980 N. The spring index is 6.8 and the design factor of safety is 1.25. If the yield stress in shear is 770 MPa and endurance stress in shear is 350 MPa, find: 1. Size of the spring wire, 2. Diameters of the spring, 3. Number of turns of the spring, and 4. Free length of the spring. 5. Ks= shear factor 6. whals factor The compression of the spring at the maximum load is 30 mm. The modulus of rigidity for the spring material may be taken as 80 kN/mm:.
A mechanism used in a punchingmachinery consists of a tension spring assembled with a preload of 30 N. The wire diameter of spring is 2 mm with a spring index of 7. The spring has 10active coils. The spring wire is hard drawn and oil tempered having the following material properties:Design shear stress = 780 MPa Modulus of rigidity = 80 kN/mm2Identify (a) the initial torsional shear stress in the wire, (b) the spring rate, and (c) the force to cause the body of the spring to reach its yield strength.
Problem 4: A helical compression spring is to be cycled between 150 lbf and 300 lbf with a 1-in stroke. The number of cycles is low, so fatigue is not an issue. The coil must fit in a 2.1-in diameter hole with a 0.1-in clearance all the way around the spring. Use unpeened music wire with squared and ground ends. (a) Determine a suitable wire diameter, using a spring index of C = 7. (b) Determine a suitable mean coil diameter. (c) Determine the necessary spring constant. (d) Determine a suitable total number of coils. (e) Determine the necessary free length so that if the spring were compressed to its solid length, there would be no yielding
A spring made from music wire ASTM 228 steel has the following data:Free length=1.75” Outside diameter=0.561”Wire diameter=0.055” Applied load= 14 lbEnds=square and ground both ends hingedNumber of coils=10 G=11.85 x 106psi E= 30 Mpsi Findspring rate, force at solid length,check for buckling,coil clearance and hole diameter
A helical compression spring has a scale of 500 lb/in., an outside diameter of 2.75 in, a free length of 8 inches and with squared and ground ends. The load is 1,000 lbs and the working stress on the wire material is 65000 psi. If the Wahl factor of 1.25 is to be used, calculate the following: A. The standard wire diameter B. The number of active coil if G = 10 800 000 psi C. The solid height D. The stress at solid height
A helical compression spring is required to provide a minimum force of 150 lb at installation and have a working deflection of 1 in. The spring rate is 75 lb/in. The coil must fit in a 2.1-in-dia hole with 0.1 in total clearance. Use 0.25-in diameter unpeened music wire and squared/ground ends. Use a 15% clash allowance, shear modulus G = 11.5 Mpsi, and weight density γ = 0.285 lb/in3. Assume Sys = 0.6Sut. Part A Find the shear stress at the initial deflection. Express your answer in pounds per square inch to three significant figures. τiτi = Part B Find the mean stress. Express your answer in pounds per square inch to three significant figures. Part C Find the alternating stress in the coil. Express your answer in pounds per square inch to three significant figures. Part D Find the fatigue safety factor for infinite life in shear. Express your answer using three significant figures.…
A helical compression spring is made with oil-tempered wire of diameter 0.2", mean coil diameter of 2", 12 total coils, 5" free length, and squared ends. (a) Find the solid length. (b) Find the force required to compress the spring to closure? (c) Find the factor of safety against yield when compressed to the solid length. (Hint: Uses Say= 0.5 Sut for shear strength.)
A helical compression spring shown in figure, experience a minimum force of 150 lb at just before ignition. During the working cycle it experiences addition force as it is compressed by an inch. The spring rate is 50 lb/in. The coil must fit in a 2.1-in-dia hole with 0.1 in clearance. Use 0.25 in diameter, peened, OQ&T wire and squared/ground ends. Find a) The stresses and safety factor for infinite life fatigue. b) Calculate the number of the coils. (Shear modulus G= 11.5 x10^6 psi) Note that for peened springs, Zimmerli's finding is updated as follows: Ssa = 57.5 kpsi (398 MPa) and Ssm = 77.5 kpsi (534 MPa) Expansion Just before Ignition
PROBLEM: 5 A helical valve spring is to be designed for an operating load range of 90N to 195N. The maximum deflection of the spring for this load range is 7.5 mm. Assuming a spring index of 9, a permissible shear stress of 550 N/mm2 for the material and the modulus of rigidity of 0.85x105 N/mm2. Determine the dimensions of the spring. (i.e. Diameter of the spring wire ,Mean coil diameter, Outer diameter of the spring, number of active turn and free length of the spring). Assume the spring coil is squared and ground.