A helical spring is to be designed for an operating approximately (90N to 135 N). A helical spring is to load of range The deflection of the spring for the load range is (5 mm). Assume a spring index of 10. Permissible shear stress for spring material (4 80 MPa): - . ring stress Modulus of rigidity(80 MPa). Design the spring? *

Q: Consider the equation for angular twist due to torsion. Imagine you are designing a solid round…

A: The angular distortion of an item caused by a couple of twisting torques is known as the angle of…

Q: salve gine a- when

A: givendifferential equation xdydx+cosy=0y=π4  when x=2

Q: A bcc (111) surface has the following (3x1) adsorbate structure: Select all of the following LEED…

A: Solution: Given Data:

Q: solve both

A: Power input, Gear speed of input shaft, Gear ratio, Power loss,

Q: (b) Compute the internal torque exerted on gear A (TAC), gear C(TcD) and gear D (TDB). (c) Sketch…

A:

Q: What is the maximum magnitude of the bending moment caused by force G? If none, enter zero. Do not…

A: It is required to determine the magnitude of the maximum bending moment by the force G.

Q: Water falls vertically downward from an open faucet with an initial velocity of 47 cm/s. If the…

A:

Q: Draw the box closing mechanism given in the figure in the given dimensions. Determine the velocities…

A:

Q: can you resolve and draw the fbd

A: Freebody diagram of the cut section:

Q: LA 5 mm 28 mm ー-ギー - 49 mm 49 mm

A: For triangle, X1= 0 Y1= (1/3)×95= 31.67 mm  A1 = 1/2 × 98× 95 = 4655 mm2 For semi circle, X2 =0 Y2=…

Q: ldentify the valvetrain components in the drawings. Place the identifying letter next to the name of…

A: Valve train get together for a gas powered motor contains a typical transporter which upholds the…

Q: solve frist one please

A: The diametral pitch of each gear:center distance of the gears:Velocity ratio:

Q: Q1 The 45° strain rosette is mounted on a surface of the bracket as shown in Figure Q1. The bracket…

A:

Q: y D 1 m FD

A: Given data:     The given load is: FD=100 kN The given angle is: θ=73˚ The distance between the load…

Q: Thank you for your help. I was able to get them all but can't get F correct. Could you help me with…

A:

Q: 200 mm В

A:

Q: 620 mm 125 350 mm

A: Consider the line diagram of the following figure as shown below – From the line diagram, it is…

Q: Add the length of all the horizontal pieces. They go left and right.

A:

Q: D raio s.f.D and B.M.

A:

Q: What is the length and wall thickness of the vertical bear

A: For figure 2,  drawing and the type of symbols present

Q: Fload/8 Fload/4 ffort = Fload/8

A: According to the details provided in the question, we need to calculate  we need to find all forces…

Q: As shown, a section of a roller coaster track (Eigure 3) follows the form of y = (2/3)x¹.5 Locate…

A:

Q: So what is the answer? What is y (1)? What is the answer up to two decimal places.

A: y(1) for equation of motion

Q: A piezometer and a pitot tube (close to each other, as described in the figure) are connected to the…

A:

Q: Choose three types of Reuleaux lower pairs, and answer the following, F.1 Write down their names?…

A:

Q: A multi-stage pump, 260 gpm capacity is installed in a well 27 ft below the static water level.…

A: Given data:  The capacity of the pump is given as Q = 260 gpm = 0.579 ft3/sThe total discharge head…

Q: Incorrect please resolve both parta

A: To calculate the surface temperature of the tank when it is passed through water and to calculate…

Q: Crossed center lines are used in the .. . view Longitudinal Horizontal Circular All

A: Solution:

Q: Calculate the number of degrees of freedom The value must be a number 11 Calculate the number of…

A: Full joint is the joint which has area or surface contact, and half joint is the joint which has…

Q: A) Are all the nodes in the same plane?. B) To the surface, what would the unit of perpendicular…

A: The 3 dimensional geometric coordinates of the system are taken in uniform units as millimetre. They…

Buckling of columns

The column is described as a vertical member of the structure that carries an axial compressive load, and buckling is a lateral deformation of the column under the application of load.