In the given circuit, a step down transformer with an RMS voltage as 220V | 22 V is used with RL = 3 KN. %3D Assume diode as Silicon and the input frequency is F= 70 Hz. A D3 D1 AC in D2 D4 LOAD B 1- Name the given circuit . 2- Find The PIV. 3- Find Current trough load resistance. 4- Draw the Input and Output wave forms.

In the given circuit, a step down transformer with an RMS voltage as 220V | 22 V is used with RL = 3 KN. %3D Assume diode as Silicon and the input frequency is F= 70 Hz. A D3 D1 AC in D2 D4 LOAD B 1- Name the given circuit . 2- Find The PIV. 3- Find Current trough load resistance. 4- Draw the Input and Output wave forms.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Design a DC power supply using FWR to perform the following requirements. Find V_dc, V_rms, V-ripple, PIV of the diode. draw the waveform of (V_in, V_out, L_in, I_load, V_diode and I_diode). Input voltage = 25 Transformer turn ratio 0.1 load resistance = 1k ohm Ripple factor = 0.025 Diode type =Si
For the given circuit below, a step down transformer gives an RMS voltage of 230 V/ 10.2-0-10.2 V with a load resistance of 2.2 Kiloohms. Assume Silicon diodes are used. Determine the Peak Inverse Voltage of the diode. D, SCT RL D. llle ண
The ripple factor for pure dc is Answer: For the given circuit below, it operates on a peak-to-peak input voltage of 390.1 V, F= 60 Hz household supply through a step-down transformer with turns N1 = 10 and N2 = 1. Silicon diodes are used with a 1 Kiloohms load. Determine the output peak voltage (in volts). D1, D2 AC Input Vsec (Source) .03 D4 Load O 27.31 O 18.11 O 13.93 O 20.91
In the given circuit, a step down transformer with an RMS voltage as 220V/ 22 V is used with R = 3 KO. Assume diode as Silicon and the input frequency is F= 70 Hz. D3 D1 AC in D2 D4 LOAD 1- Name the given circuit 2- Find The PIIV. 3- Find Current trough load resistance. 4 Draw the Input and Output wave forms.
4. For the circuit shown in the figure below uses a transformer of 230V/12V-0-12V and all diodes are Ge find the following, RL-3.3k2. The name of the circuit is ........ Current through the load is............The DC output voltage is............ Draw the input & output wave forms ✈ ellel eetee CT D₂ DE www R₂
Q5. For the following center tapped transformer, show the waveform across each half of the secondary winding and across Ri, when a 100 V peak sine wave is applied to the primarywinding. What is the PIV rating must the diode have? (Use constant voltage drop model for the Silicon diode) D1 IN4001 R. V out OV 10 kN D2 IN4001 llle
For the given circuit below, a step down transformer gives an RMS voitage of 230 V/ 12-0-12 V with a load resistance of 22 Kiloohms. Assume Silicon diodes are used. Determine the Peak Inverse Voltage of the diode. O 33.94 O 26.83 O 16.97 O 21.17 A silicon diode in a half-wave rectifier has a barrier potential of 0.7 V. This has the effect of reducing the peak input voltage by 0.7 V. increasing the peak input voltage by 0.7v. no effect. increasing the peak output voltage by 0.7 V. Next nane
Question-4: In the bridge type circuit shown below, the diodes are assumed to be ideal. The transformer is specified to have a 15 Vrms secondary voltage. Find: A- D.C. output voltage Vp(out). B- Peak inverse voltage PIV. 1:4 +100 V D. D V. ov -100 V Vp(out) D 10 kf) elle
Explain five (5) applications of the hall effects With the aid of a diagram, explain how a P-N Junction is form. iii. State five (5) application of PN Junction, and explain the property of the PN junction that make those application possible. Explain what carrier mobility is and elaborate on the factors that influence carrier mobility. A 80 V rms is stepped down to 18V rms by a transformer. The output from the transformer is rectified using a half wave rectifier circuit and connected to a 47.5 Ω load resistor. Draw a circuit diagram of this arrangement and the waveform at each stage. Calculate the following about the circuit in Figure 2.1 (If silicon diodes are employed in the rectification); the peak value of the output voltage considering the drop across each diode, the average voltage, iii. The current through the load resistor, The current diode, The frequency of the output signal, Calculate the efficiency of the full wave rectifier expressed in percentage. vii. Sketch…
What is the value of the average voltage at the output of the circuit in the figure, knowing that: Voltage at the transformer output is equal to 5 Vac and the four diodes are from the 1N4001 family.
The step up chopper has R=20 ohm and out put voltage is 120V. The source voltage is 40V DC . The load inductance is 0.2mH. If the chopper frequency is 4KHZ find1- the duty cycle2- the average value of source current3- TON4- Imax5- Imin6-The average value of diode current
If the input voltage for the given circuit below is 220 V at 60 Hz the load resistance (RL) is 560n and the average output voltage is 30 V. Assume the diodes to be germanium diodes. Determine the turns ratio of the transformer used. If a capacitor of 120 pF is connected parallel to the load resistor (RL), Determine the ripple factor. DI D2 V D3 D4 RL a. The turns ratio of transformer (Npri/Nsec) is b. The Ripple factor is eeleer