how many 15 mm holes will be required to keep the cover plate in position?

Q: A steel tube of 200 mm external diameter is to be shrunk onto another steel tube of 60 mm internal…

A: For inner tube: Write the expressions for A and B for thick cylinder. At r=0.030,…

Q: Calculate the bearing stress and shear stress between the pin and each bracket of a clevis joint.…

A:

Q: 1.4 Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly…

A: The normal stress (either tensile or compressive) developed in a member when it is subjected to an…

Q: The lap joint shown is fastened by five % inch-diameter rivets. The bearing stress in the plates is…

A:

Q: Solve the following problem of a steel tensile plate with a concentrated load applied at the top, as…

A:

Q: A U-bolt supports a load of 5,000 lb. The cross-section of the bolt has a diameter of ½ in. How…

A: Given: Load supported by the U-bolt = P=5000 lb Diameter of bolt = d=0.5 in

Q: (a) What pressure can the cylinder carry if the permissible tangential stress is psi and the theory…

A:

Q: A Steel wire hangs vertically under its weight. What is the greatest length it can have if the…

A: given; allowable tensile stress(σ)=200MPa…

Q: find the required wall thickness of the cylinder.

A: find the required wall thickness of the cylinder.

Q: Two circular rods of 50mm diameter are connected by a knuckle joint, by a pin of 40 mm in diameter.…

A: Given:Diameter of circular rod, D=50 mmDiameter of pin, d=40 mmPull load, P=120 kN=120*103 NFind:1…

Q: walled vessels is assumed to apply? ssure found in part (a), compute the s

A:

Q: The figure shows a roof truss and the detail of connection at joint I. The allowable stresses are 70…

A:

Q: A small seat angle is used to support a beam with a reaction of 6,000 lbs. Two 1/2 inch diameter…

A:

Q: mum weight of cylinder th your answer in two decimal

A: given:

Q: A tank 10 m high and 2 m in diameter is 15 mm thick. The max tangential stress is ? The max…

A: Given data  height = 10 m diameter = 2 m thickness = 15 mm find the maximum tangential stress and…

Q: rmine the support reaction at D pade of solid cvlindors: ARİS S

A:

Q: 4. The cross sectional area of each member of the truss is 1.6 in?. Calculate the stresses in…

A: GIVEN DATA - A PLANE TRUSS GIVEN WITH AREA 1.6in2 WE HAVE TO FIND STRESS IN GIVEN MEMBER

Q: SETB: A cylindrical steel pressure vessel 400 mm in diameter with a wall thickness of 18 mm, is…

A:

Q: is a 150 mm long rectangular plate (thickness 10 mm and height 70mm). There are two circular notches…

A:

Q: Determine the stress in the cable at B, g

A: Need to determine the stress in cable at B.

Q: A stainless steel tube with an outside diameter of 52 mm and a wall thickness of 5 mm is used as a…

A:

Q: A hydraulic press is shown in the figure. When the press squeezes any material, P force occurs in…

A: Given data: Length of the press, l = 100 mm. Width of the press, b= 80 mm. The factor of safety, n…

Q: -28 The steel pipe column shown in Fig. P2-28a has an out- side diameter of 150 mm and a wall…

A:

Q: What wall thickness in mm is required for a 634 mm diameter cylinder under an internal pressure of…

A:

Q: A thick cylinder has an outside diameter of 100 mm and an inside diameter of 60 mm. It is…

A:

Q: Required : 1. Determine the safest thickness of the vessel in mm 2. If the vessel has spherical…

A:

Q: b- 10 mm diameter of Brinall hardness ball when the load 500 kgr and HB= 300 determined the diameter…

A: Given: Diameter of the ball=10mmBrinall hardness =300Loading=500kg.f

Q: A bar ACB has is subjected to an external load at C, and it is supported either end by a cable as…

A:

Q: A column is made of the two materials side by side as shown. Each material carries a portion of the…

A:

Q: A steam boiler is to have a 300-mm-diameter hand hole placed on one end. If the maximum internal…

A: Stress is defined as the the force acting per unit area. It is given that total allowable stress is…

Q: in 5 minutes please Diameter=38 L

A:

Q: 6. A PIPE CARRY|NG STE AM AT 3.5 MPa HAS AN OUTSIDE DIAMETER OF 450 mm AND A WALL THICKNESS OF 1D…

A: force, F=σ×AF=3.5×π4×4302F=508270.42 NP=F

Q: PROBLEM 2 Given is a truss structure: Where: Working shear stress for the rivets is 70 MPa Working…

A:

Q: A steel boiler 2.5 m in diameter has a wall thickness of 25 mm. The internal pressure is 1.6 MPa.…

A: Given: d=2.5 m t=25 mm P=1.6 MPa S=250 MPa

Q: Calculate the minimum diameter for a cylindrical vessel that is to carry a gas at a pressure of 10…

A: Given  Pressure = 10 MPa Thickness of vessel = 38mm Hoops stress = 83MPa Pd/2t = 83 10d/(2×38)=83…

Q: Define the main difference between thick and thin cylinders and give an example for each type of…

A:

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.