Find the residual hoop stress at the internal surface of a thick-walled cylinder made of a material with yield strength of 500 MPa, the inner and outer radii of 100 and 150 mm, respectively. The cylinder was initially subjected to the fully plastic pressure and after that the pressure was released. O 114 MPa O-281 MPa O-318 MPa O-117 MPa 245 MPa - 230 MPa

Find the residual hoop stress at the internal surface of a thick-walled cylinder made of a material with yield strength of 500 MPa, the inner and outer radii of 100 and 150 mm, respectively. The cylinder was initially subjected to the fully plastic pressure and after that the pressure was released. O 114 MPa O-281 MPa O-318 MPa O-117 MPa 245 MPa - 230 MPa

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.5.11P: The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in...

See similar textbooks

Similar questions

The wall thickness of a 1.2 m diameter spherical tank is 1.6875 mm. Calculate the allowable internal pressure if the stress is limited to 55 MPa. If i will get the same answer again I will report and downvote.
How to find circumferencial stress in the cylindrical vessel. Give the equations.
The ring, with dimensions shown, is placed over a flexible membrane which is pumped up with a pressure p. The thickness r,-r; is small compared to r; (a) Determine the axial force F in the ring in terms of p, w and r;. Hint: Consider a FBD by cutting the ring+membrane in two. (b) Determine the hoop stress in the ring. (c) Determine the hoop strain in the ring. The modulus of elasticity for the ring is E. (d) Relate the hoop strain to the change in the inner radius of the ring after this pressure is applied, and use this to get the change in the inner radius in terms of p, E, w, r, and ri- (PLEASE ANSWER ASAP AND CORRECTLY)!
The cylinder head of the gas engine has a dimension of a 254 mm x 450 mm. There are ten (10) bolts on the block. The explosion pressure is 14 kg/cm² and the studs are made of ordinary bolt material, with Sy = 606,760 kPa Find the stress area in in².
Assume the plane stress element shown in Fig. E3-a represents the stress a geosynthetic membrane used in a mechanically stabilized earth wall. If the reference state of stress for this element results in the Mohr’s circle plot shown in Fig. E3-b, determine: The principal stresses. The principal directions (angles to the principal planes). The maximum in-plane shear stress. It is known that the seam, which is rotated 45 deg from the vertical as shown in Fig. E3-c, will fail if subjected to a tensile stress of 25 kPa or a shear stress of 1 kPa. Determine the normal stress and shear stress acting on the seam, and state if the seam will fail due to the loading indicated.
The cylinder is shown in Figure is made of steel having a specific weightof gst = 490 lb>ft3. Determine the average compressive stress acting atpoints A and B.
An cylinder is 30 cm in diameter and the steam pressure is 7 kg/cm. If the cylinder head is held by 12 studs, find the size, assume safe tensile stress as 280 N/mm
A cylindrical pressure vessel is fabricated from steel plating that has a thickness of 30 mm. The outer diamter and thickness of the pressure vessel is 500 mm and 10 mm. Its length is 2m. Determine the maximum internal pressure (MPa) that can be applied if the longitudinal stress is limited to 155 MPa, and the circumferencial stress is limited to 55 MPa.
1) A cylindrical pressure vessel is fabricated from steel plating that has a thickness of 20 mm. The diameter of the pressure vessel is 450 mm, and it's length is 2.0 m. Determine the maximum internal pressure that can be applied if the longitudinal stress is limited to 140 MPa and the circumferential stress is limited to 60 MPa 2) A compound thin cylinder has a common diameter of 100 mm, and the inner cylinder has a thickness of 2,5 mm. The radial pressure between the two cylinders is 200 KPa and the difference between the two common diameters before shrinkage was 0,004305 mm. E=200 GPa Determine : A) Thickness of the outer cylinder B) Resultant hoop stresses in both cylinders if the compound cylinder is subjected to an internal pressure of 180 KPa
The cylinder pressure vessel has an inner radius of 1.25 m and a wall thickness of15 mm. It is made from steel plates that are welded along the 45oseam. The vesselis internally pressurized by 10 Mpa. a. Is it a thin or thick wall? b. What are the general state of stresses for this problem? c. Is it plane stress problem? d. Using Mohr’s circle, find out the principle stresses. e. What would be the shear stress values associated with the principle stresses? f. Determine the normal and shear stress components along this seam, usinganalytical equation, and then show the normal stress and shear stress componentsin your Mohr’s circle. ONLY A,B & C PLEASE
41.) A cylindrical steel pressure vessel 400 mm in diameter with a wallthickness of 20 mm, is subjected to an internal pressure of 7.875 MPa. Towhat value may the internal pressure be increased if the stress in the steelis limited to 100 MPa?
A copper bar with a rectangular cross sectionis held without stress between rigid supports (seefigure). Subsequently, the temperature of the bar israised 50°C.(a) Determine the stresses on all faces of theelements A and B, and show these stresseson sketches of the elements. (Assumeα = 17.5 x 10 6 / °C 2 and E = 120 GPa.)(b) If the shear stress at B is known to be 48 MPaat some inclination θ, find angle θ and showthe stresses on a sketch of a properly orientedelement.