6. A PIPE CARRY|NG STE AM AT 3.5 MPa HAS AN OUTSIDE DIAMETER OF 450 mm AND A WALL THICKNESS OF 1D mm. A GASKET IS INSERTED BETWEEN THE FLANGE AT ONE END OF THE PIPE AND A FLAT PLATE USED TO CAP THE END. HOW MANY 40 mm- DIAMETER BOLTS MUST BE USED TO HOLD THE CAP ON IF THE ALLOWABLE STRESS IN THE BOLTS IS 105 MPa, OF WHICH 55 MPa IS THE INITIAL STRESS? WNHAT CIRCUMFERENTIAL IN THE PIPE ? TO TIGHTEN THE BOLT INITIALLY AND WHAT WILL STRESS IS DEVELOP WHY IS IT NECESSARY HAPPEN IF THE STEAM PRESSURE SHOULD CAUSE THE STRESS IN THE BOLTS TO BE TWICE THE VALUE OF THE INIIAL STRESS ?

6. A PIPE CARRY|NG STE AM AT 3.5 MPa HAS AN OUTSIDE DIAMETER OF 450 mm AND A WALL THICKNESS OF 1D mm. A GASKET IS INSERTED BETWEEN THE FLANGE AT ONE END OF THE PIPE AND A FLAT PLATE USED TO CAP THE END. HOW MANY 40 mm- DIAMETER BOLTS MUST BE USED TO HOLD THE CAP ON IF THE ALLOWABLE STRESS IN THE BOLTS IS 105 MPa, OF WHICH 55 MPa IS THE INITIAL STRESS? WNHAT CIRCUMFERENTIAL IN THE PIPE ? TO TIGHTEN THE BOLT INITIALLY AND WHAT WILL STRESS IS DEVELOP WHY IS IT NECESSARY HAPPEN IF THE STEAM PRESSURE SHOULD CAUSE THE STRESS IN THE BOLTS TO BE TWICE THE VALUE OF THE INIIAL STRESS ?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A Ansle erson E leg the radius of the cylinder. and Fig. 10.19 Problems 10.3 and 10.4 The Anstwer: r = 0.26 m pove.
SolveSample Problem 4.1.All remain as presented, except for the following changes.The factor ofsafety is now 2, and not 3.As Presented, the thickness of the tube is uniform. In the new one that you are solving,let the thicknessesof the top and bottom be the same,ttb, and the thicknesses of theleft and right be the same,tlr.Theheightand the width of the tube are still respectively 5 in and 3.25 in.As you make thesethickness changes,you are to keep thetotal mass of the tube unchanged. Answer the same questions (a) and (b).Explain your findings
W hen the galvanized irn sheets comewith dim ensions (2x1)m.Calculate the num ber of sheets equired to m ade the ectangular duct system shown in figure below when it sized using equal friction m ethod w ith frictionalpressure dop of 1pam and alow able height is 300 m m. 0.6 m /s 0.6 m/s 2. D 2m 2m 2m| F 2m Fan E 2m B A 5m
A cast Aluminum crlinder o f a Portable hodrawlic 208 Mm in diameter The 16,8 N/mm2 by gauge riveter is Pressure. of The fluid is Determine Sui table thicknesS of the inder wall assuming that the Yield Point stress 442 N/mm2 And factor of safety of 6.2 Calculate. the tangential and radial streses middle radius and at the inner outer surface.
A welded steel cylindrical drum made of a 10-mm plate has an internal diameter of 1.20 m. Compute the change in diameter that would be caused by an internal pressure of 1.5 MPa. Assume that Poisson's ratio is 0.30 and E = 200 GPa. OLAd 0.459 mm OIL. Ad Ⓒ III. Ad = 0.289 mm ON. Ad 0.369 mm 0.521 mm
Q3: (a) describe the location and function of the following: \i. Gudgeon pin ii. Rod shank ii.Large end (b) Determine the thickness of a plain cylinder head for 0.3m cylinder. The maximum gas pressure is approximately 3.2N/mm. Design the studs also for the cylinder cover. Assume the allowable hoop stress =42 N/mm' for cast iron; the allowable tensile stress for material of studs =63 N/mm?
1) A set of pipes are available with 50-mm inner-diameter and varying outer-diameters from 51 mm to 53 mm in 0.2 mm increments. A pipe from this set will be used connected to a motor to transmit a power of 110 kW when the pipe is turning at 6000/z rpm without exceeding an allowable stress of 12 MPa, What is the outer diameter of the lightest usable pipe for this cause?
Q2 ) A cone clutch is to transmit 10 KW at 600 r.p.m. the cone has aface angle of 10◦The width of the face is halfe of the mean radius and the max pressureis 0.1 N/mm²Assuming uniform wear and the coefficient of friction is 0.3, find theinner and outer radius and the axial force required on the clutch.
Q2/ Compute the burst-pressure rating for 10.75-in., J-55 casing having a nominal wall thickness of 0.40 in., and a nominal weight per foot 45.5 Ibm/ft.
E AA 2.2 Description An aluminium manifold (shown in Figure 1), is used to convey low pressure air from a supply source to an electronic device. The manifold is manufactured from a square block of aluminium, which is machined using a CNC milling machine. During the manufacturing process of the manifold, two machining setups are required (need to be machined from two sides), resulting in additional set up and machining time required for the manufacturing of the manifold. 96,00 78,00 18,00 20,00 07.00 1.60 Ø18,00 Ø14,00 10,00 SECTION A-A Figure 1: Draft views of the aluminium ma II 00'06 INN 00'S 00'96
3. a. Determine the thickness of a steel air receiver with 30in. diameter and a pressure of 120psi, design stress of 8000psi b.draw the possible bursting scenario for the problem
Based on the standard requirement of a system, it is given that the diameter of the bore ofcylinders for clamping and drilling processes are 100 mm and 80 mm, respectively. It isexpected that the clamping process will take a load of 700N while 650N will be loaded fordrilling process. The speed movement for the clamping and drilling process is designed to be120cm/min and 180mm/min, respectively.i. Compute the required flowrate for the pump for both clamping and drillingprocesses. ii. Calculate the working pressure required for the system if only one cylinder is tobe choose for both clamping and drilling processes. iii. Which horse power of the motor is required?