I need it in 5 minutes pleaseDiameter=38Length=0.8 Rigid member AC is supported by a pin at A and the vertical steel link BD as shown. Thediameter of the link and its length are given in the table below for each student. The alloawblestress of link BD is 200 MPa.a) Determine the maximum possible value of the load Pb) If P-90 kN, determine the change in temperature needed for link BD to have no changein length.Given asteel 12*10-6/ºC, Esteel 200 GPaPA0.4m0.2m

Answered: Image /qna-images/answer/87a2cd12-8b4e-428d-a6a4-72f608f45a39.jpg

Answered: in 5 minutes please Diameter=38 L

Engineering

Mechanical Engineering

in 5 minutes please Diameter=38 L

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Rigid member AC is supported by a pin at A and the vertical steel link BD as shown. The diameter of the link and its length are given in the table below for cach student. The alloawble stress of link BD is 200 MPa. a) Determine the maximum possible value of the load P b) If P-90 kN, determine the change in temperature needed for link BD to have no change in length. Given Me=12*10/"C, E,200 GPa B A 0.4m 0.2m
Q1- The rigid bar of negligible weight is supported as shown in Fig- IS W- 80 kN, compute the temperature change of the assembly that will cause a tensile stress of 50 MPa in the steel rod. Use the following data: Bre Steel 15 m A (mm') a (/c°) 110m E (GPa) Steel rod 300 Bronze rod 1400 11.7* 10* 200 18.9 10 25m 83
Use the Method of Sections to find the load in member EK of the bridge. Is it in tension or compression? Record your answer in kN. A B Q 1m P 1m 1m N 1m M 1m 1m K 1m 1m 1m 10kN 10kN 10kN 10kN 10kN 10kN 10kN 10kN 10kN 1m, H 2m
2m 9. The rod AB rests on a horizantal surface at A and against slipping suface at B if Ms =0-25 at A&B. Find the minimum distance a for equilibriam, negledt the weight ( Ans a-l-6lm) a 60N • peu m7 jo
ZV. 0 3 ull ull zain 1Q zain IQ The rod BD is made of material with G1= 110 GPa has a diameter 18 mm is bonded to the tube CA at point B, the tube made of material with G2=187 GPa has an outer diameter 41 mm and wall thickness of 10 mm. If T1=1424 N.m and T2=2563 :N.m, answer the following questions A B T2 N-m 0.4 m 0.1 m D 0.3 m T1 N-m The polar moment of inertia of the rod BD is إجابتك The polar moment of inertia of the tube CA is احابتك
A bar, 12 mm in diameter is acted upon by an axial load of 20 kN. The change in diameter is measured as 0.03 mm. DeterminePoisson’s ratioYoung’s modulusBulk modulus Assume modulus of rigidity as 80 GPa
E. Rigid bar AD is horizontal before the weight of 112 lb is applied to the end of wire BC at C. The wires have a radius of 0.025" and are made of A913 steel. Determine the rotation of AD and how far C will move down due to application of the weight See Appendix of text for any material properties needed. Ans: 0.00071 radians 3 ft - 2 ft -3 ft- D B 4 ft W
Q1/ A bracket is supported by means of 4 rivets of the same size. Design the 7. Alalkau diameter of the rivet if Ou (tenşile ultimate stress) for the rivet material is 560MPA. Which of the rivet has max resistance? 20KN 20KN B0mm 30 mm 30 mm 30 mm
If load P = 22.9 kips, determine the normal force in bar (1). D P A 6 ft 51.9 kips 44.8 kips 27.3 kips 38.2 kips O 40.4 kips B (1) 4 ft
The figureshows a copper rod that is placed in an aluminum tube. The rod is 0.005 in. longer than the tube of length L = 10.14 in. Find the maximum safe load P (in lb with four decimal places) that can be applied to the bearing plate, using the following data: area of copper = 2.78 sq, in. area of aluminum = 3.28 sq, in. E of copper = 17013025 ksi E of aluminum = 10072240 ksi allowable stress for copper = 19000 ksi allowable stress for aluminum = 10802 ksi
If load P = 20.3 kips, determine the normal force in bar (1). D A 6 ft 43.8 kips 31.0 kips 33.8 kips 20.3 kips 39.3 kips B (1) 4 ft
Let's considera rod having a solid circular cross-section with diameter of 4 mm and it is made of a material having a Young's modulus E= 200 Gpa and a Poisson's ratio of 0.3. If a tensile force Fis subjected to that rod cross-section, the diameter becomes 3.995 mm. determine the applied force F Select one: OF 5236 N O F=15708 N Clear mopshoe Finish attempt