he shaft, shown below, consists of rods AB and CD and a tubular segment BC. The rods are onnected with the tubular segment using bolts at B and C. If a torque T is applied to the shaft, etermine: a) the number of bolts required for the connection at B or C. Use 15 mm-diameter bolts with Tallow=50 MPa. The bolts are located at a radial distance p measured from the longitudinal axis of the shaft. b) The diameter of the solid rods AB and CD. Given that the allowable stress for the shaft is Tallow=140 MPa. T (kN.m) p (m) 27 0.4

he shaft, shown below, consists of rods AB and CD and a tubular segment BC. The rods are onnected with the tubular segment using bolts at B and C. If a torque T is applied to the shaft, etermine: a) the number of bolts required for the connection at B or C. Use 15 mm-diameter bolts with Tallow=50 MPa. The bolts are located at a radial distance p measured from the longitudinal axis of the shaft. b) The diameter of the solid rods AB and CD. Given that the allowable stress for the shaft is Tallow=140 MPa. T (kN.m) p (m) 27 0.4

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

- once answered Correctly will UPVOTE!!
Six 30 mm diameter bolts in the outer bold circle of 370 mm radius are steel A T and six 20 mm diameter bolt in the inner bolt circle of 260 mm diameter are aluminum. What is the torque capacity of the coupling? Assume that the allowable shearing stress for the steel bolts is 40 Mpa and aluminum bolts of 30 Mpa. The Shear modulus of elasticity of aluminum and steel are 28 Gpa and 84 Gpa, respectively. P2 P1 R2 R1 1. 757 T°C Despejado A GGn G8/11/202 O Escribe aquí para buscar acer
A steel shaft ABC connecting three gears consists of a solid bar of diameter d between gearsA and B and a hollow bar of outside diameter 1.25d and inside diameter d between gears Band C. The shear modulus of elasticity for the shaft is 80 GPa. a) What is the minimumpermissible diameter d if the allowable shear stress in the shaft is 80 MPa? b) What is theminimum permissible diameter d if the angle of twist between any two gears is limited to 4.0º?
Parvinbhai
Question 4 fixed. The shear modulus G and the polar moment of inertia I, of the bar's cross-section are constant along the bar's axis. From the fixed left end (x = 0) of the bar to the middle (x = L/2) of the bar, a lincarly varying distributed torque t, = kr, 0 < x < L/2 is applied (the unit of t, is N-m/m). At the free end (r = L) of the bar, a concentrated torque T is applied (the unit of T is N-m). According to the right-hand rule, the linearly varying distributed torque t, and the concentrated torque T both point to the r-positive direction. Find the angle of twist at the free end (x = L) (Expressing the result with G, Ip, L, T, and k). (Hint: It is easier to find the angle of twist using & = f Figure 1 shows a bar under torsion. The left end of the bar is E.) t, = kx L/2 L/2 Fig. 1. The left end (r = 0) of the bar is fixed, and the right end (r = L) of the bar is applied with a concentrated torque T. A linearly varying distributed torque t, is applied from the left end (z = 0) of…
Please solve, include the diagrams, and do not copy from other bartleby answers. Handwritten solution is more preferred than typed. A flanged bolt coupling connects two shafts. The bolt circle diameter is 250 mm in which there are 12 bolts. The allowable shear stress is 56 MPa in the shafts and 22 MPa in the bolts. One shaft is hollow with outside diameter of 100 mm, while the other one is solid of diameter 50 mm. Determine the ratio of the outside and inside diameter of the hollow shaft and the bolt diameter so that both shafts and the flanged bolt coupling are having the same strength in torsion.
4. A flange bolt coupling consists of 12-14mm diameter steel bolts on a bolt circle 320mm in diameter and 8-12mm diameter steel on a concentric bolt circle 260mm in diameter. What torque can be applied without exceeding a shearing stress of 60MPa in the bolts? B) Determine the number of 10mm steel bolts that must be used on the 320mm bolt circle of the coupling to increase the torque capacity by 6KN-m.
4) The C-clamp shown below has rectangular cross-section A-A that is 33 mm tall by 12 mm wide and the material is class 50 gray cast iron. Determine maximum tensile stress and factor of safety for clamping force F = 3.2 kN. Ignore stress concentration factors. See Section 4.9 in Norton for help with curved beams. MPa N O MAX |F F 60 mm 40 mm 12 mm 33 mm 33 mm Section A-A A
O A hollow circular shaft of inner radius 10 mm outer radius 20 mm and length 1 m is to be used as a torsional spring. If the shear modulus of the material of the shaft is 150 GPa, the torsional stiffness of the shaft (in kN-m/rad) is (correct to two decimal places).
Question 2 A composite shaft is comprised of a solid inner rod (shaft 1) made of a steel with an elastic modulus of 210 GPa, diameter of 70 mm, and length of 100 mm, and a hollow outer shaft (shaft 2) made of the aluminium with an elastic modulus 80 GPa, outer diameter of 100 mm, inner diameter of 80 mm, and a length of 100 mm that are rigidly attached to one another on both ends. The composite shaft is designed to absorb 150 joules of energy for deformation within its linear elastic limit upon application of an axial load onto a collar attached to its lower end. Determine the stresses induced in shafts 1 and 2, magnitude of the forces acting on shafts 1 and 2, and the total force acting on the composite shaft for the cases of: (i) A gradually applied load. (ii) A suddenly applied load. (iii) A mass that is dropped onto the collar from a height of 250 mm.