A power source at C actuates valves at A and B through a long round steel control rod. A torque of 8.5 kN.m is required to actuate each valve. If the allowable shear stress in the control rod is 80 MPa, determine a) what diameters are required for each section of the rod. B) what is the angle of twist in the rod between the power source at C and the valve at A. Draw the torque diagram for the assembly. Use G = 83 * 103 MPa

A power source at C actuates valves at A and B through a long round steel control rod. A torque of 8.5 kN.m is required to actuate each valve. If the allowable shear stress in the control rod is 80 MPa, determine a) what diameters are required for each section of the rod. B) what is the angle of twist in the rod between the power source at C and the valve at A. Draw the torque diagram for the assembly. Use G = 83 * 103 MPa

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Write the nature of work done by an elongated spring?
Need help with engineering Materials review problem
Please solve 1 and 2 with neat good explainations please
Give me right solution with clear steps
Need help on all questions. Please include all units, steps to the problem and information such as its direction or if it is in compression or tension. Thx.
Q7 For the bracket shown in the figure: > The moment of the force (1000N) about pin A is...... > The moment of the force (1000N) about pin B is...... The moment of the force (1000N) about pin C is. 600mm 1000 N 500mm 200mm 240 N.m CCW, 562 N.m CCW, 1099 N.m CCW 200 N.m CW, 468 N.m CW, 915 N.m CW 562 N.m CW, 1099 N.m CW, 240 N.m CW 468 N.m CW, 915 N.m CW, 200 N.m CW O GOOD LUCK! Eiminer Asst. Lecturer. Reem Al-Timimi Head of the Department Dr. Hussein Sadig
3- Draw Torque vs. angle oi twist for Cast Iron specimen
Problem 3: Design engineers in many situations must justify their selection of beams and pin-ended columns used in various machines. Your role in a mechanical design company that manufactures gearbox and gearbox mounting platform is to analyse the rolled steel beams and columns under study. Your manager asked you to properly select one rolled steel beam and one rolled steel column for the design and to provide your justification of this selection, if the following design requirements are given: - Beams and columns are made of ASTM-A709/Grade-345 Factor of Safety (F.S) is 1.2 Buckling Euler conditions must be met. Beams are subjected to 50 kN axial force. Beam (A) has radius of 10 mm. Beam (B) has radius of 5 mm. Column (A) is subjected to 15 kN axial force. Column (A) has length of 1.5 m and radius of 10 mm. Column (B) is subjected to 15 kN axial force. Column (B) has length of 1.5 m and radius of 13 mm. P P A B Figure.3: Rolled steel beams. P P A P P Id B Figure.4: Rolled steel…
Solution: 2 of 4 Problem 2: The short cylindrical block of 2014-T6 aluminum, having an original diameter of 0.5 in. and a length of 1.5 in., is placed in the smooth jaws of a vise and squeezed until the axial load applied is 800 lb. Given young's modulus 10.6x10 psi and Poisson ratio equal to 0.35. a) Determine the decrease in its length b) Determine its new diameter. 800 Ib 800 Ib Solution:
4. Schedule 40 pipe is to be used in a torsion application. The power applied is to be 200 hp and the pipe material is to be SAE 1141 OQT 900 steel. The loading is to be repeated. ( 400 RPM) Text book: Applied strength of Material 6th (a) Calculate the maximum allowable shear stress for the steel. (b) Calculate the smallest size of schedule 40 pipe
2.) An automobile lift raises a car weighing 3000 lbf, 6 ft off the shop floor (Fig. 2-12). Assuming the lift itself weighs 500 lbf and th at friction is negligible , what is the worknecessary to raise the car in ft-Ibf and m-N ?
QUESTION 2 A 13-kN hydraulic press for removing and reinstalling bearings in small-to medium-sized electric motors is to consist of a commercially available cylinder mounted vertically in a C- frame, with dimensions as sketched in the Figure shown below. It is being proposed to use ASTM A-48 (Class 50) gray cast iron (brittle material with ultimate strength, Su 345 MPa) for the C-frame material. Calculate the bending moment about the centroidal axis upto 3 digits after decimal point in KN.m? 18 mm 38 mm 13 kN 25 mm 10 mm -90 mm 10 mm 1.805 Save A Click Save and Submit to save and submit. Click Save All Answers to save all answers. arch DELL