1. Question: With a pin on the AB beam A and a short lever BC as shown in the figure is supported. A, B and C pins have a diameter of 18 mm. P and a are given together Take as values given opposite your names in the table. This upload is above, below in your name on the pin (column 5 Calculate the shear stress occurring on only one of the specified pins A, B and C). P(kN)=30 a(°)=60 pin=A 4P 4P 2P 0.5 m 0.5m 1.5 m 1.5 m B

1. Question: With a pin on the AB beam A and a short lever BC as shown in the figure is supported. A, B and C pins have a diameter of 18 mm. P and a are given together Take as values given opposite your names in the table. This upload is above, below in your name on the pin (column 5 Calculate the shear stress occurring on only one of the specified pins A, B and C). P(kN)=30 a(°)=60 pin=A 4P 4P 2P 0.5 m 0.5m 1.5 m 1.5 m B

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

My id 78 ASAP
In (Figure 1), w = 3.8 kip/ft and F=20 lb. Follow the sign convention. Part A Determine the shear force acting at point D of the beam. Express your answer in kilopounds to three significant figures. vec VD = kip Figure 1 of 1 Submit Request Answer Part B Determine the moment acting at point D of the beam. Express your answer in kilopound-feet to three significant figures. A, 6 ft 9 ft ΑΣφ vec MD = kip ft %3D
Subject: Statics of Rigid Bodies
Q/ For the beams and loading shown below. A-Draw the shear force and bending-moment diagrams. B- Determine the equations of the shear force and bending-moment curves for the segments CD in Figure 2 C- Compute the bending stress at point (a) on section C. D- Determine the values and locations of the maximum tensile and compression bending stresses. Figure (2) R Point a Radius of hole: 40kN 0.5m 30 20KN/m 0.7m A B D |B 1m Im 3m Radius = R= 100 mm
I-section built-in beam in the figure shows two forces It is in effect. These forces at point A and B stress element by finding the stresses that it generates Please show on. Note: force of 100 kN It is in the x-y plane and the point of action is Take as its surface. Force with a magnitude of 180 kN I is in the center of gravity of the section (Search all show transactions and required reductions
5 The best size wire is fitted in a groove of a metric screw such that the wire touches the flanks of the thread on the pitch line as shown in the figure. The pitch (p) and included angle of the thread are 4 mm and 60°, respectively. The diameter of the best size wire is mm (round off to 2 decimal places). Pitch line Flank 60⁰ Wire 0.25p -0.5p-
The lifting arm shown below needs to lift a weight of 4 (N). Assuming the links are weightless, determine the magnitude of the force being applied by the pin at B on the lifting arm to the nearest hundredth of a newton. 10Em) 6icm- 150 A Servo Horn Arm 4 (W) 'Servo
Please answer this question as soon as possible
2: The forces acting on gear-shaft-bearing system are shown in the figure given below. a) Calculate the force Fg b) Find the support reactions at 0 and C c) Obtain the bending moment diagrams (M, and My) d) Obtain the torque diagram (Mx) e) Calculate o (bending stress) and t (torsional shear stress) at a point where the maximum bending moment is observed f) For this point, compute the principal and maximum shear stresses 400 mm 350 mm 25° 300 mm FA= 11 kN olo 20° 50-mm dia. A Gear A, 600-mm dia. /C B Gear B, 300-mm dia.
Find all the non-zero components of internal reaction forces in section a-a. If you select wrong answers, you will have negative score in this question. 200 mm 200mm D 400 N 800 N
solve all parts. show all steps/solutions. show equations for shear and moment diagrams show full solution and fbds