h F The beam of length 5.9 (m) and cross section base 0.10 (m) and height 0.16 (m) shown is made of plain steel with a modulus of elasticity of 200 (Gpa) and an ultimate strength of 400 (Mpa). The load is 250 (N) and the point q is 4.0 (m) from the wall in the x direction. What is the magnitude of vertical deflection of the beam

h F The beam of length 5.9 (m) and cross section base 0.10 (m) and height 0.16 (m) shown is made of plain steel with a modulus of elasticity of 200 (Gpa) and an ultimate strength of 400 (Mpa). The load is 250 (N) and the point q is 4.0 (m) from the wall in the x direction. What is the magnitude of vertical deflection of the beam

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter9: Deflections Of Beams

Section: Chapter Questions

Problem 9.5.4P: Beam ABC is loaded by a uniform load q and point load P at joint C. Using the method of...

See similar textbooks

Similar questions

.2 A ligmio.irc ii supported by two vorlical beams consistins: of thin-walled, tapered circular lubes (see ligure part at. for purposes of this analysis, each beam may be represented as a cantilever AB of length L = 8.0 m subjected to a lateral load P = 2.4 kN at the free end. The tubes have a constant thickness ; = 10.0 mm and average diameters dA = 90 mm and dB = 270 mm at ends A and B, re s pec lively. Because the thickness is small compared to the diameters, the moment of inerlia at any cross section may be obtained from the formula / = jrrf3;/8 (see Case 22, Appendix E); therefore, the section modulus mav be obtained from the formula S = trdhlA. (a) At what dislance A from the free end docs the maximum bending stress occur? What is the magnitude trllul of the maximum bending stress? What is the ratio of the maximum stress to the largest stress (b) Repeat part (a) if concentrated load P is applied upward at A and downward uniform load q {-x) = 2PIL is applied over the entire beam as shown in the figure part b What is the ratio of the maximum stress to the stress at the location of maximum moment?
Beam ABC is loaded by a uniform load q and point load P at joint C. Using the method of superposition, calculate the deflection at joint C. Assume that L = 4 m, a =2ra, q = 15 kN/m, P = 7.5 kN, £ = 200 GPa, and / = 70.8 X 106 mm4.
A beam of uniform rectangular section 200 mm wide and 300 mm deep is simply supported at its ends. It carries a uniformly distributed load of 9 KN/m run over the entire span of 5 m. if the value of E for the beam material is 1 X 104 N/mm2 , find the slope at the supports and maximum deflection. Give me complete solution based on the given above. Again I need to ask the same question since you gave me a wrong answer before.
The shape of the beam made of U profile ensures safe loading. Find the length c of the overhangs so that it can move. Of the material Safety stress (ç) emn = 50 N / mm2 for tension and compression conditions, (ob) emn = 80 N / mm2. Support spacing of the beam L = 6 m, cross section its dimensions are a = %D 210 mm, b = 150 mm and wall thickness t = 40 mm. The loading condition is P = 30 kN and qo = 40 kN / m. P B (Kesit)
For the beam and loading shown, use the double-integration method to determine (a) the equation of the elastic curve for the beam, (b) the slope at A, (c) the slope at B, and (d) the deflection at midspan. Assume that El is constant for the beam. Let Mo = 50KN-m, L= 4.5 m, E= 180 GPa, and I = 115x 106 mm4. Mo B Answer: (b) 0A = i rad (c) Og = i rad (d) vmid = i mm
beam, simply supported at its ends, carries a load which increases uniformly from 15kN/m at the left-hand end to 100 kN/m at the right-hand end. If the beam is 5m long, find the equation for the rate of loading and, using this, to determine the deflection of the beam at mid-span if E= 200GN/m² and I=600*10 m².
A I-meter-long, simply supported copper beam (E= 117 GPa) carries uniformly distributed load q. The maximum deflection is measured as 1.5 mm. a. Calculate the magnitude of the distributed load q if the beam has a rectangular cross section (width b= 20 mm, height h= 40 mm). b. If instead the beam has circular cross section and q= 500 N/m, calculate the radius r of the cross section. Neglect the weight of the beam.
Materials 2 Time: 40 Minutes Q1) The figure shows a simply supported beam with overhang portion, carrying loads under different points. Using Macaulay's methods to determine the slope and deflection at points: A, B and at 1m from the left hand end of the beam. Take EI=0.65 MN/m². 20 kN 20 kN 30 kN/m B -0.6m. 1.2 m. 1.2 m. Ra 8 A
Question Two For the shown simply supported beam, a deflection of 1.5 mm is developed in the beam at x 0.75 m when a L mm, of P=500 g is applied. If the beam has a rectangular cross section of b= 35 mm and h = 51 find the modulu: elasticity of the beam's material. 0.6 m 0.6 m
2. A square glass reinforced plastic plate 3 mm thick is simply supported along all the edges. The plate is subjected to uniform distributed load q. The elastic properties of the plate are: Ex = 40 kN/mm², E, = 8 kN/mm², Gxy = 4 kN/mm², µHxy = Hyx = 0.25. Obtain an expression for deflection function of the plate using Levy's solution. Also determine the maximum deflection of the plate. Take origin at the top left corner of the plate.
The dimensions are of the graph are d1 = 7 cm , L1 = 6 m , d2 = 4.2 cm , and L2 = 5 m with applied loads F1 = 130 kN and F2 = 60 kN . The modulus of elasticity is E = 80 GPa . Use the following steps to find the deflection at point D. Point B is halfway between points A and C. What is the reaction force at A? Let a positive reaction force be to the right.
Q1/ A beam AB of span 8 meters is simply supported at the ends, as shown in Fig. 1. It carries a uniformly distributed of 30kN/m over its entire length and a concentrated load of 60kN at meters from the support A. Determine the maximum deflection in the beam and the location where the deflection occurs. Take E=200*106 KN/m² and 1=24*10m². 3m KN/M 60x C 30kN/m 5m