Q1/ A beam AB of span 8 meters is simply supported at the ends, as shown in Fig. 1. It carries a uniformly distributed of 30kN/m over its entire length and a concentrated load of 60kN at meters from the support A. Determine the maximum deflection in the beam and the location where the deflection occurs. Take E=200*106 KN/m2 and 1=24*10m². 3m KN/M 600 30kN/m 5m

Q1/ A beam AB of span 8 meters is simply supported at the ends, as shown in Fig. 1. It carries a uniformly distributed of 30kN/m over its entire length and a concentrated load of 60kN at meters from the support A. Determine the maximum deflection in the beam and the location where the deflection occurs. Take E=200106 KN/m2 and 1=2410m². 3m KN/M 600 30kN/m 5m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q2: For the beam shown in figur , determine the value of I that will limit the maximum deflection to 20 mm. Use E=10*10° N/m?. 600 N/m- 1m 2 m
beam, simply supported at its ends, carries a load which increases uniformly from 15kN/m at the left-hand end to 100 kN/m at the right-hand end. If the beam is 5m long, find the equation for the rate of loading and, using this, to determine the deflection of the beam at mid-span if E= 200GN/m² and I=600*10 m².
A beam of uniform rectangular section 200 mm wide and 300 mm deep is simply supported at its ends. It carries a uniformly distributed load of 9 KN/m run over the entire span of 5 m. if the value of E for the beam material is 1 X 104 N/mm2 , find the slope at the supports and maximum deflection. Give me complete solution based on the given above. Again I need to ask the same question since you gave me a wrong answer before.
Q 2. Calculate the slope and deflection at the free end of the cantilever beam shown in figure using Method of super position Take. E = 2.05 x 10$ N/mm2 and I = Y x 10% mm“. %3D If the last two digits of student id 2 50, then take Y = last two digits of id /100. If the last two digits of student id < 50, then take Y = last two digits of id /10; If last two digits of id are zeroes, then take Y= 0.75 2 kN 6 kN/m 1.2 kN-m 3 m 2.2 EI
A simply supported beam of 6 m length with external diameter 150 mm and thickness15 mm has maximum deflection 4.25 mm at the centre. Calculate the uniformlydistributed load carried over by the beam. Take E=210 kN/mm
Question Two For the shown simply supported beam, a deflection of 1.5 mm is developed in the beam at x 0.75 m when a L mm, of P=500 g is applied. If the beam has a rectangular cross section of b= 35 mm and h = 51 find the modulu: elasticity of the beam's material. 0.6 m 0.6 m
Question 5 calculate the deflection of the point C in mm of a rigid beam AB which is supported by a spring as shown in the diagram below. NE 2 m 1 kN 3m 181 N/mm
Question 2 A beam ABC of length 3m has one support at the left end and the other support at a distance 2m from the left end. The beam carries an uniformly distributed load W=16 kN/m. Given E = 2 x 10$ N/mm? and I = 80 × 106 mm4. a. Find the slopes at the left support A. b. Find the deflection at the right end c. Find the maximum deflection between the supports. W A C 2 m 3 m Figure 2.
A I-meter-long, simply supported copper beam (E= 117 GPa) carries uniformly distributed load q. The maximum deflection is measured as 1.5 mm. a. Calculate the magnitude of the distributed load q if the beam has a rectangular cross section (width b= 20 mm, height h= 40 mm). b. If instead the beam has circular cross section and q= 500 N/m, calculate the radius r of the cross section. Neglect the weight of the beam.
For the beam and loading shown, use the double-integration method to determine (a) the equation of the elastic curve for the beam, (b) the slope at A, (c) the slope at B, and (d) the deflection at midspan. Assume that El is constant for the beam. Let Mo = 50KN-m, L= 4.5 m, E= 180 GPa, and I = 115x 106 mm4. Mo B Answer: (b) 0A = i rad (c) Og = i rad (d) vmid = i mm
Question 5 calculate the deflection of the point C in mm of a rigid beam AB which is supported by a spring as shown in the diagram below. 2 m 1 kN 3m 157 N/mm
Situation 2 | Beam ABCDEFG below is subjected to multiple loads as show. The total length of the beam is 10m. Analyze the beam completely. 6 kN 10 kN 3 kN/m 2 kN 5 kN-m G 3000mm. 1000mm 1000mm. 2000mm. 1000mm 2000mm.