A bronze bar is fastened between a steel bar and an aluminum bar as shown in Fig. p-211. Axial loads are applied at the positions indicated. Find the largest value of P that will not exceed an overall deformation of 3.0 mm, or the following stresses: 140 MPa in the steel, 120 MPa in the bronze, and 80 MPa in the aluminum. Assume that the assembly is suitably braced to prevent buckling. Use Est = 200 GPa, Eal = 70 GPa, and Ebr = 83 GPa. Steel A = 480 mm² 1.0 m Bronze A = 650 mm² 3P 4P 2.0 m Figure D-211 Aluminum A = 320 mm² 1.5 m 2P

A bronze bar is fastened between a steel bar and an aluminum bar as shown in Fig. p-211. Axial loads are applied at the positions indicated. Find the largest value of P that will not exceed an overall deformation of 3.0 mm, or the following stresses: 140 MPa in the steel, 120 MPa in the bronze, and 80 MPa in the aluminum. Assume that the assembly is suitably braced to prevent buckling. Use Est = 200 GPa, Eal = 70 GPa, and Ebr = 83 GPa. Steel A = 480 mm² 1.0 m Bronze A = 650 mm² 3P 4P 2.0 m Figure D-211 Aluminum A = 320 mm² 1.5 m 2P

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

An unstiffened web I-section fabricated from a 10 mm thick plate by fillet welding as shown in the figure. If yield stress of steel is 250 MPa, the maximum shear load that section can is take is [2 Marks] 10 mm 300 mm 10 mm 200 mm
QI/ An aluminum bar carries the axial loads at the positions shown in Fig. 1, below. The diameter for part AB, BC and CD is 35 mm, 40 mm and 30 mm, respectively. The elastic modulus for aluminum is 72.4 x 10 N/mm. Determine the internal stresses at section (A-B), (B-C) and (C- D), and the elongation (AL) in length at each part of aluminum due to loading. в D 37 kN 10 kN 45 kN 18 kN 1000 mm 800 mm I 600 mm Fig. 1
A steel component is subjected to alternate cyclical loading. The steel follows Basquin's law for high cycle fatigue, o, x N = C, (where the stress amplitude is in MPa). Ignore the geometric detail and assume that Marin's modifying factors are all equal to 1. You are given the minimum stress ain = -213 MPa, the maximum stress omax = 213 MPa. The material data are Tensile strength oUTS = 539 MPa, Basquin's constant c, = 875 MPa, Basquin's exponent a = 0.085. a) Calculate the stress ratio R, the stress amplitude o, in MPa and the mean stress am in MPa. The answers are acceptable with a tolerance of 0.01 for R and of 1 MPa the stresses. R: MPa MPа b) Calculate the corresponding life, in 10° cycles, (tolerance of 0.1 106 cycles) N :
E 0.4m D 10KN 0.8m 0.4m В 5KN 0.6m Al 20KN A=800 mm? A=1,200 mm?
Problem 1 An axial force of P is applied to the center of the rigid end plate shown below. If the portion of the load carried by the aluminum plates is half the portion of the load carried by the brass core, (a) determine the value of h, (b) the total load if the stress in the brass is 50 MPa. Brass core (E = 105 GPa) Aluminum plates (E = 70 GPa) Rigid end plate 300 mm 60 mim 40 mm
A mild steel bar has a gauge length of 80 mm and the total elongation is 0.08 mm, find the strain produced in it.
What do you call the stress caused by the application of couple in the material?
#4 will upvote to anyone who will answer
Please answer in detailed solution and explain step by step
The light rigid bar ABCD shown is pinned at C and connected to two vertical rods. The bar was initially horizontal, and the rods were stress-free before the load P = 20 KN is applied. %3D Steel E200 GPa A-600mm L1 m 2.0 m 0.6 m 1.5 m Pa20 KN Aluminum E-70 GPa A=900mm L-1.5 m What is the ratio of the deformation of steel to deformation of aluminum?
Which of the following parameter represents principal stresses: T_a none of the available option O_X O_y 0_a
What is another term for bend? (A) flex B compress fracture D) twist E stretch