Answered: For the beam and loading shown,…

For the beam and loading shown, calculate (a) the equation of the elastic curve, (b) the deflection at point B, (c) the deflection at point C. A L2 B - 1.2 Wo C X

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The cantilever beam consists of a rectangular structural steel tube shape [E = 29,000 ksi; I = 1720 in.4). For the loading shown, determine: (a) the beam deflection at point A. (b) the beam deflection at point B. Assume MA - 170 kip-ft, P = 30 kips, LAB - 5.7 ft, Lgc = 8.6 ft. P MA A B LAB LBC Answer: (a) VA = in. (b) vB - in.
Please provide a detailed solution especiallyl for the moment of inertia and how you got the values etc. The book of Beer's manual solution does not provide a detailed solutino and it is hard to understand.
250 mm A D P = 25 kN B 30 60 C TOP VIEW 280 mm Member AD is fabricated by joining two bars (E0=205GP,, Ga=82GPA) and is pinned to plate ABC using a 5 mm diameter pins as shown in the figure. The yield strength of the pins is T,=890MPA. Plate ABC is a right triangle and is fixed along its edge BC. A 25KN Force P is then applied at end D causing a lateral strain in member AD with magnitude equal to 7.5x10-mm/mm. This also causes Point A to displace only along the horizontal resulting to a shear strain at point A equal to y,=+0.00165rad. Determine the following: 1. Poisson's ratio of material used in member AD, vAD 2. The normal strain in member AD, caD 3. The average stress experienced by pin A, T, 4. Factor of Safety of pin A with respect to yielding, FS,A 5. Displacement of point D, A,
P=wa B A -X C W -2a- For the cantilever beam and loading shown, determine Part 1 (a) the equation of the elastic curve for portion AB of the beam, (b) the deflection at B (c) the slope at B
Determine the equations of the elastic curve for the beam using the X1 and X2 coordinates. Specify the beam's maximum deflection. EI is constant. Use the double integration method.
Question 2. AP A 1 0.4m 0,5m d=20mm d= 60mm Both partion of rod ABC are made of an aluminum for which E= 704Ppa. Knowing that the magnitude of P is 4 KM, Determine; (a) the volue of Q so that the deflection at A is zero. 8. (b) the corresponding deflection of
The cantilever beam consists of a rectangular structural steel tube shape [E = 29,000 ksi; I = 1860 in.“]. For the loading shown, determine: (a) the beam deflection at point A. (b) the beam deflection at point B. Assume MA = 180 kip-ft, P = 12 kips, LAB = 3.8 ft, LBC = 5.7 ft. MA A B LAB LBC Answer: (a) VA = in. (b) VB = in.
Measure the width of the web of the cross- section of the cross-section of the T-beam in the figure with millimeter accuracy, when the yield strength of the aluminum material of the beam is 280 MPa and n = 1.5 is desired for the reliability. The width of the beam flange is 50 mm and the height is 14 mm, while the height of the web is 39 mm. The beam is loaded with a point force F = 3 kN and a distributed force q = 6 kN / m, and its dimensions are a = 0.6 m, b %3D = 0.5 m and c = 0.5 m. %3D Absolute value of bending torque Max = ? kNm Width of the web (integer) = ? mm
Please solve this problem in double integration method
The cantilever beam consists of a rectangular structural steel tube shape [E = 29,000 ksi; | = 1960 in.4]. For the loading shown, determine: (a) the beam deflection at point A. (b) the beam deflection at point B. Assume MA = 160 kip-ft, P = 17 kips, LAB = 6.4 ft, LBC = 9.6 ft. AP MA A B C LAB LBC Answer: (a) VA = in. (b) VB = in.
Text: A beam is clamped at A. The beam is supported by a uniformly distributed load and a concentrated load as indicated on the sketch. The beam is made using the HE220A profile. The length of the beam is 4200 mm. and has a modulus of elasticity on it 2,0x105N/mm2 A) Calculate the bearing reactions of the beam for the given external load action. B) Establish moment and shear diagram for the beam for the given external load action. C) Calculate the transverse displacement of the free (cantilevered) end for the given external load action. D) Calculate the rotation of the free (cantilevered) end for the given external load action.
J- A distributed load op w (kulm) is applied over the entire tength OF a simply supported beam Gm long . The beam section is as shown. Determine the maximum value OF w iF Of Ś 1OMP , and yE 800KP. 80 mm X 200 mm 360mm 200mm