The piece of plastic is originally rectangular. After the application of force, it deformed in the position shown. If a = 2 mm, b = 1.5 mm, and c = 4 mm, determine the normal strain in diagonal BC and the shear stress in corners A and C

Q: B An aluminum rod AB of diameter 3.4 inches is connected to a lever of length L = 5.8 feet. Consider…

A:

Q: C. Steel bar whose length of 1 + 0.DD m and a radius of 10+MM mm. is subjected to torque which…

A:

Q: 5 The supports of Beam AD are aluminum rod and st eel rod only. Determine the stress in the aluminum…

A:

Q: TRUE OR FALSE ONLY. PLEASE HELP 1. Area of shear diagram is equal to the magnitude of bending…

A: 1) True It is true that area of shear diagram is equal to the magnitude of the Bending moment. 2)…

Q: 400 Material A 300 Material B 200 Material A 100 0.002 0.004 0.006

A: Solution: B) Given Data: Tensile load=88 kNElastic modulus of material A=150 GPaElastic modulus of…

Q: A rigid bar AB is supported by three rods. A load P = 375 kN is applied to the bar. The modulus of…

A:

Q: A 4.QQ m B C 4.QQ m 1.5P D E 4.QQ m DO 3.TT m

A: For the truss shown, determine the safe value of P

Q: A beam with a T-section is supported and loaded as shown in the figure. The cross section has width…

A: A beam with the T section is given in the question all the loading condition is given in the above…

Q: Q1) Three bars AB, CD and ED are used to support ACE beam. The three bares have modulus of…

A: Draw the free body diagram. Equilibrium of vertical forces,…

Q: A rigid bar AB is hinged at A and is supported by a rod CD at C. The rod is pin connected at D, as…

A:

Q: The bronze bar 3 m long with a cross-sectional area of 450 mm² is placed between two rigid walls. At…

A: Given: L = 3m, A = 450mm2 Find: Temperature at which the compressive stress equals = 33MPa

Q: A cast-iron beam has a section as shown in the figure below. The beam is subjected to Q2…

A: ASKED: To determine the width of the flange of the beam.   Given, Width of flange (X) = ? mm…

Q: Determine the stress in rod if tensile force applied of 35 N having cross sectional area of 50 mm2

A: Given  Tensile force F= 35 N Crossectional area A= 50 mm2

Q: Four-25-mm-diameter rivets with an axial load of T= 75 kN distributed equally as shown. The…

A:

Q: F cross section cut Ec, A Est, Ast

A: Given data: EstEc=6AstAc=19

Q: Determine principal stress and maximum shear stress

A: Given data : Normal stress in x direction σX=750 psiNormal stress in Y direction σY=600 psiShear…

Q: The beam is loaded by two point forces P. The beam is assembled according to the cross-sectional…

A: Dimension of beam:Upper plank = 25 mm×260 mmVertical plank = 220 mm×50 mmLongitudnal direction of…

Q: 2. Two rods connected as shown carry a vertical load of 20 kN. Rod AB is a steel rod with E = 2 X10³…

A: Given data  EAB = 2 × 105 N/mm2  EBC = 7 × 104 N/mm2  LAB = 3m = 3000 mm  LBC = 2m = 2000 mm  A =…

Q: bar is horizontal and the rods are stress-free. Determine the stress in each rod if temperature of…

A: EquilibriumPA=2 PCσAAA =2σcACσA300=2σC1200σA=8σC

Q: The stress at a point is shown on the element. Determine (a) principal stress, (b) maximum in-plane…

A:

Q: P+ D P

A: Given a single acting rivet connecting two steel plates having rivet diameter 22 mm, thickness of…

Q: Ultimate strength is the highest ordinate in the tress-strain diagram.

A: Power can be defined as energy divided by time. The unit of power is watt. Power and time are…

Q: Required information. Consider the given state of stress. Take X= 16 MPa and Y= 48 MPa. Y + X 60 MPa…

A:

Q: For the beam shown, calculate the bending stress at a point 70 mm. from the top of the beam. P = 59,…

A:

Q: ouble tee cross section is used for the beam shown below. Assume the following lengths and loads: 14…

A:

Q: The two bars are made of polystyrene, which has the stress-strain diagram shown. If the…

A: Given : Cross sectional area of bar AB is = 975 mm2 Cross Sectional area of bar BC = 2600 mm2…

Q: The bronze bar 3.08 m long with a cross-sectional area of 629 mm2 is placed between two rigid walls.…

A:

Q: Part 2 * Your answer is incorrect. The z-component of momemt M will cause compression at A and B,…

A:

Q: UPVOTE will be given! Please write the solutions completely and legiby. Box the final answer. Answer…

A: Solution: Given: P = 40 kN a = 25 mm b = 30 mm c = 70 mm

Q: Two bars are made of a material with the stress-strain diagram as shown. Find the cross-sectional…

A:

Q: A 31 mm diameter bronze bar 3.7 m long is placed between two rigid walls. At a temperature of -39°C,…

A:

Q: ProbleT --- An aluminum bar has diameter d = 40 mm, shear modulus of elasticity G = 27 GPa, and…

A: Simple stress is expressed as σ=PA, it is force per unit area. Shear stress is developed is applied…

Q: The mean dimensions of the cross section of the leading edge and torsion box of an airplane wing can…

A: Given data,  G = 19 GPa Average shear stress = 158 MPa Wall thickness = 12 mm   To find out the…

Q: If the beam is subjected to an internal moment of M = 30 kN.m, determine the maximum bending stress…

A: Given : M = 20 kN-m This is a problem of Solid mechanics where we have to find the max. bending…

Pressure and Stress