The cantilever beam consists of a rectangular structural steel tube shape [E = 29,000 ksi; I = 1900 in."). For the loading shown,determine:(a) the beam deflection at point A.(b) the beam deflection at point B.Assume Ma = 190 kip-ft, P= 19 kips, LAB = 3.0 ft, Lgc = 4.5 ft.MALABLBCAnswer:(a) VA=in.(b) vg =in.

given-a cantilever beam of rectangular cross section. required- To find deflection of beam at point…

Answered: (a) the beam deflection (b) the beam…

Engineering

Civil Engineering

(a) the beam deflection (b) the beam deflection at point A. at point B.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 8. Exercise: Observation Target Face left Face right reading The following Table shows the field…

A: To Determine Accepted mean angles, A, B , C , D.

Q: . A 5-m clay layer lies beneath an 8-m sand layer. The sand is 3 meters below the water surface.…

Q: A pump helps bring oil (SG 0.8) to reservoir D from reservoir A at 235 liters per %3D second. The…

Q: Find the approximate flow rate at which water will flow in a conduit shaped in the form of an…

Q: For theloading shown, use the double-integration method to determine (a) the equation of the elastic…

Q: Determine the velocity of car K.E=550 J Mass=25 kg

A: Introduction : In this question we are provided with value of kinetic energy and value of mass of…

Q: Reflection on Green concrete technology

A: Green concrete technology What is Green Concrete Technology Green Concrete is a revolutionary topic…

Q: A standard HS truck is moving across a 25-m simple span. The wheel loads are Pa = 36 kN, Pb = 142…

Q: eam and loading shown, use discontinuity functions to compute ope of the beam at C (positive if…

Q: MB

Q: y loaded connection is subjected to a service-load shear force of 250 kN and a service-load tensile…

A: Given:- service-load shear force= 250 kN service-load tensile force =500 kN. The loads are 60% dead…

Q: Find the value of water content if weight of water is 5 g and weight of soil solid is 45 g

A: Given data : The value of weight of water in soil mass WW=5 g The value of weight of soil solids…

Q: The simply supported beam consists of a W460 × 82 structural steel wide-flange shape [E = 200 GPa; I…

Q: 15 A slope 60 ft high has a face inclination of 30°. Uniform soils comprise the slope and foundation…

A: We have to solve part b

Q: What is the capacity of a flight conveyor of 8 inches by 18 inches travelling at 100 ft/min and…

A: The values given in the question are as follows: Conveyor width(b)=18 in or 1.5 ft Conveyor…

Q: 2. (a) A retaining wall 6 m high with a vertical back supports a cohesionless soil with a dry unit…

A: Earth Pressure:The stress caused in a body due to the external load applied to it is called earth…

Q: r the cantilever steel beam [E = 220 GPa; I = 102 x 106 mm*), use the double-integration method to…

Q: The shown beam cross-section has f' 4,000 psi and f, 60,000 psi. Determine the depth of th neutral…

A: Given:- The compressive strength of the concrete = f'c = 4000 psi The yield strength of the steel =…

Q: What are the reasons why Pump station water is metered.

A: Reasons for the metering of pump station can be various, it can be for monitoring purpose or can be…

Q: n the crest gate on a dam shown in the figure, surface AB forms the arc of a circle of 6 m radius…

A: Figure is as shown

Q: A one cell rapid sand filter tank has a loading rate 9.0 m/h, surface dimensions of 15*6 m. The sand…

A: Loading rate= 9.0m/hDimensions b×d=15×6mgravel depth = 70cmwash trough = 50cmheight of water=…

Q: For the beam and loading shown, use discontinuity functions to compute (a) the slope of the beam at…

Q: ind the angle e given that x = 20 Newtons, y = 99 Newtons, and o = 37 degrees. Note that the thread…

A: x=20N y=99N

Q: or F = 500! 3 m 2 m 2 m of Determine and express the results in Cartesian vector 3. format: a. The…

Q: Athin wire is bent into frame having a shape as found in Figure 8. What is the y-centroid of this…

A: The dimensions of wire object are given in the figureThe wires are divded into sections to calculate…

Q: 50 kN 50 kN B 20 kN/m D 1 m 4 m 1m

Q: 4. Given A vehicle changes velocity from 80.0 km/hr to 20.0 km/hr in 6.00 seconds. Required: Find…

Q: Hello can you provide me 3 research title ideas in civil engineering that is unique and possible…

A: Research Title based on Geotechnical Engineering 1 Stabilisation of Karewa soil using Glass Fibre…

Q: Q20 The moment connection shown generates a maximum tensile or compressive load of 222.8 kips at…

A: Given that a structural tee connect the beam to the column Diameter of bolts (D) = 3/4 inch Dead…

Q: A turbine is rated at 600 HP (output) when the flow of water through it is 0.61 m^3/s. Assuming an…

Q: ss the theoretical determination of weir coefficients

A: The weir coefficient (as given in the weir equation above) is a single parameter that includes the…

Q: SA3) A 6-m uniform rod is acted upon by different forces at different points as shown in he…

A: Given Data:L=6mUpward loads= 3N, 4N, Downward Load= 2N, 4N, 5N.

Q: Determine the force value if work done is 15 J and displacemnt is 3 m

A: Given data : The value of work done W=15 J The value of displacement d=3 m To find : Force applied

Q: During a flow of 500 L/s the gage pressure is +68 kPa in the horizontal 300 mm supply line of a…

A: Q=500L/s = 0.5m3 /s To find output power of turbine

Q: According to the elastic theory, the vertical stress induced by a flexible line load length has an…

A: Vertical stress due to line load Vertical Stress in Soil A strip load causes vertical stress in the…

Q: 20 kN/m 60 kN A E B D -8 m -8 m- El = constant E = 70 GPa 1= 800 (106) mm4 %3D

Q: Show complete solutions with figures. A bottle consists of a cylinder 0.3 m in diameter and 0.4 m…

A: to determine the pressure of the trapped air in the bottle.

Q: more settlement beneath the center of circular load or beneath the edge of load

A: Settlement: - It is defined as the downward movement of soil when external load is applied on soil.

Q: 2. A lap joint is fastened by three 20mm diameter rivets and carries a load of 50 KN as shown.…

A: Width of plate(w)=150mm Thickness of plate(t)=25mm Diameter of river(d)=20mm Number of rivet(n)=3

Q: The simply supported beam consists of a W21x 44 str support at Dcan provideresistance either up or…

Q: A WT305 x 41 standard steel shape is used to support the loads shown. Assumew = 42 kN/m, LaB = 1.5…

Q: A frame is loaded as shown in the figure. If Q/EI is the horizontal displacement at C, what is the…

A: P = 78KN

Q: Calculate the quantities of cement, water, and fine aggregate and coarse aggregate per trial mix of…

A: Step 1: Determination of Target mean strength f'ck=fck+1.65*S= 50+1.65*5= 58.25 MPa Step 2:…

Q: From the figure as shown, the maximum shearing stress is 30 MPa and the angle of twist is 1.35°.…

Q: The strain components for a point in a body subjected to plane strain are ɛx = -520 µɛ, ɛy = -350µɛ…

Q: Calculate the quantities of cement, water, and fine aggregate and coarse aggregate per trial mix of…

A: Target mean strength= 50+1.65*5= 58.25 MPa w/c ratio =0.5 Slump value = 30-60 mm maximum size of…

Q: Problem: Formulate the shear and moment functions of the beam shown. Draw the necessary FBD. டார்…

A: To draw SFD and BMD

Q: Situation 1: Three concurrent forces are acting on the beam as shown. P2 = 60 kN P3 = 80 kN P = 25…

A: As per guidelines we need to answer only first 3 subparts of questions so please repost rest…

Q: A triaxial test is performed on a cohesionless soil. The soil failed under the following conditions:…

A: c = 0 (cohesion less soil) σ3= confining pressure = 250 kpa∆σ = deviator stress = 450 Kpa To…

Q: the beam and loading shown, use discontinuity functions to compute he slope of the beam at C…

Concept explainers

Beams

In structural engineering, a beam is a component made of a variety of materials (including steel alloys, and wood) that can resist loads applied laterally to the beam axis. Members, elements, rafters, shafts, and purlins are all terms used to describe beams.

Question

The cantilever beam consists of a rectangular structural steel tube shape [E = 29,000 ksi; I = 1900 in."). For the loading shown,
determine:
(a) the beam deflection at point A.
(b) the beam deflection at point B.
Assume Ma = 190 kip-ft, P= 19 kips, LAB = 3.0 ft, Lgc = 4.5 ft.
MA
LAB
LBC
Answer:
(a) VA=
in.
(b) vg =
in.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The cantilever beam consists of a rectangular structural steel tube shape [E = 29,000 ksi; I = 1860 in.“]. For the loading shown, determine: (a) the beam deflection at point A. (b) the beam deflection at point B. Assume MA = 180 kip-ft, P = 12 kips, LAB = 3.8 ft, LBC = 5.7 ft. MA A B LAB LBC Answer: (a) VA = in. (b) VB = in.
The cantilever beam consists of a rectangular structural steel tube shape [E = 29,000 ksi; I = 1640 in.*). For the loading shown, determine: (a) the beam deflection at point A. (b) the beam deflection at point B. Assume MA = 240 kip-ft, P = 11 kips, LAB = 3.4 ft, Lgc = 5.1 ft. P MA A B C LAB LBC Answer: (a) VA = in. (b) Vg = in.
The cantilever beam consists of a rectangular structural steel tube shape [E = 29,000 ksi; I = 1750 in.4]. For the loading shown, determine: (a) the beam deflection at point A. (b) the beam deflection at point B. Assume MA = 200 kip-ft, P = 24 kips, LAB = 6.2 ft, LBc = 9.3 ft. MA В C LAB LBC Answer: (a) VA = in. (b) VB = in.
The cantilever beam consists of a rectangular structural steel tube shape [E = 29,000 ksi; I = 1690 in.*). For the loading shown, determine: (a) the beam deflection at point A. (b) the beam deflection at point B. Assume MA = 170 kip-ft, P = 30 kips, LAB = 6.1 ft, Lec = 9.2 ft. P MA В C LAB LBC Answer: (a) VA = in. (b) Vg = in.
Q2: The simply supported beam shown as Figure 5. below is subjected to Loading as shown on the Figure. Using singularity function method. Find the maximum Lenght (L) so that the max. deflection is not greater than 30mm for the Beam.. The flexural rigidity (El) of Beam section El = 50*103 KN.m?2 “4m L Sm
The cantilever beam consists of a rectangular structural steel tube shape [E = 29,000 ksi; I = 1730 in.4]. For the loading shown, determine: (a) the beam deflection at point A. (b) the beam deflection at point B. Assume MA = 210 kip-ft, P = 13 kips, LAB = 3.8 ft, LBC= 5.7 ft. МА V A Answer: (a) VA = (b) VB= LAB P B in. in. LBC C X
Current Attempt in Progress The cantilever beam consists of a rectangular structural steel tube shape [E = 29,000 ksi; = 1990 in."). For the loading shown, determine: (a) the beam deflection at point A. (b) the beam deflection at point B. Assume MA= 250 kip-ft, P= 14 kips, LAB = 4.1 ft, LBc = 6.2 ft. MA LAB LBC Answer: in. (a) VA- in. (b) VB - 4. Submi Attempts: 0 of 1 used Save for Later
The cantilever beam consists of a rectangular structural steel tube shape [E = 29,000 ksi; I = 1720 in.4). For the loading shown, determine: (a) the beam deflection at point A. (b) the beam deflection at point B. Assume MA - 170 kip-ft, P = 30 kips, LAB - 5.7 ft, Lgc = 8.6 ft. P MA A B LAB LBC Answer: (a) VA = in. (b) vB - in.
The cantilever beam consists of a rectangular structural steel tube shape [E = 29,000 ksi; I = 1570 in.“]. For the loading shown, determine: (a) the beam deflection at point A. (b) the beam deflection at point B. Assume MA = 160 kip-ft, P = 10 kips, LAB = 9.0 ft, LBC = 13.5 ft. MA A В C LAB LBC Answer: (a) VA = in. (b) Ув in.
The cantilever beam consists of a rectangular structural steel tube shape[E = 29,000 ksi; I = 1640 in.4]. For the loading shown, determine: (a) the beam deflection at point A. (b) the bean deflection at point B. Assume MA = 160 kip-ft, P = 18 kips, LAB = 4.7 ft, Lec = 7.1 ft. MA A B LAB LBC Answer: (a) VA = in, (b) vg = in.
The cantilever beam consists of a rectangular structural steel tube shape [E = 29,000 ksi; I = 1500 in.“]. For the loading shown, determine: (a) the beam deflection at point A. (b) the beam deflection at point B. Assume MA = 150 kip-ft, P = 26 kips, LAB = 6.1 ft, LBC = 9.2 ft. MA A LAB LBC
The cantilever beam consists of a rectangular structural steel tube shape [E = 29,000 ksi; | = 1960 in.4]. For the loading shown, determine: (a) the beam deflection at point A. (b) the beam deflection at point B. Assume MA = 160 kip-ft, P = 17 kips, LAB = 6.4 ft, LBC = 9.6 ft. AP MA A B C LAB LBC Answer: (a) VA = in. (b) VB = in.