12.8. A portal frame made from members of equal plastic moment of resistance Pl/2 is loaded as shown in Figure 12.23. Find the critical collapse mechanism and the corresponding value of A. Verify that this mechanism satisfies the yield condition by drawing the bending moment diagram. AP B Til A с 2AP D E 777777 1/2

12.8. A portal frame made from members of equal plastic moment of resistance Pl/2 is loaded as shown in Figure 12.23. Find the critical collapse mechanism and the corresponding value of A. Verify that this mechanism satisfies the yield condition by drawing the bending moment diagram. AP B Til A с 2AP D E 777777 1/2

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The assembly in Fig. P-242 consists of a light rigid bar AB, pinned at O, that is attached to the steel and aluminum rods. In the position shown, bar AB is horizontal and there is a gap, A = 5 mm, between the lower end of the steel rod and its pin support at C. Compute the stress in the aluminum rod when the lower end of the steel rod is attached to its support. A 0.75 m O Steel A = 250 mm² E = 200 GPa 1.5 m Figure P-242 Aluminum L = 2 m A = 300 mm² E = 70 GPa B
Use the method of consistent deformations to determine the reaction components, and draw the shear force and bending moment diagrams for the beam shown in Fig.1. (constant EI) A B 401
Determine the support reactions for the structures shown in figure by using the method of consistent deformations. 90 kN E D 10 m 21 15 kN/m 30 kN/m 4 m 4 m E = constant
The fixed-end beam is subjected to a concentrated moment "M" at midspan as shown in Fig.1. Use the method of consistent deformations to determine the reaction components and draw the shear force and bending moment diagrams for the beam (constant EI).
Calculate the support responses and the bond strengths at the C-joint of the carrier system given in the figure. 6 kNm 4 KN 4 KN 4 kN/m B 1m A 4 m 6 m 10 KN +2m +2m D 3 m F
Compute the deformation in member 1 which is solid alumnim with a area of 214159 mm^2
k * 3m 3m A с 3m 4m (10) (5) 20 KN 3m (10) D (10) B Answers in structures lectures : Analyze the structure as shown in Fig. belows Area = ( ) cm² Ib=100 * 10³ cm4, E = 20*10³ kN/cm² 4m (5) (10) 1 E 2 Members CD, BD, DE, EF, DF & CF are truss members' Member AB is a frame member ·30.6kNim A 15.1 KN 20 KN ETABS Answers: R₁ = 15.103 kN; MA= 30.61 kN.m, FBD = 4.897 KN 4.9 KN
4.3. At a point in a structural member, yielding occurred under a state of stress given by: 40 40 50 -60 MPa -60 Determine the uni-axial tensile yield strength of the material according to (a) maximum shearing stress theory, and (b) Octahedral shearing stress theory. 4.5. Determine the width t of the cantilever of height 2t and length 0.25 m subjected to a 450 N concentrated force at its free end. Apply the maximum energy of distortion theory. The tensile and compressive strengths of the material are both 280 MPa. 4.6. Determine the required diameter of a steel transmission shaft 10 m in length and of yield strength 350 MPa. In order to resist a torque of up to 500 N.m. The shaft is supported by frictionless bearings at its ends. Design the shaft according to the maximum shear stress theory, selecting a factor of safety of 1.5, (a) neglecting the shaft weight, and (b) including the effect of shaft weight. Use y = 77 kN/m as the weight per unit volume of steel. 190 MPa 30 MPa 40 MPa…
Use the method of consistent deformations to determine the reaction components, and draw the shear force and bending moment diagrams for the beam shown in Fig.2. (El is constant). 2 m D 20 KN 2 m 2 m 10 KN B
A pin-jointed plane truss shown in Figure Q1 is supported by a roller at point A and pinned at point G. Vertical point loads of 5 kN are acting downward at points B, C and D. As a structural engineer, you are responsible to check the stability and analyse all of the members in the truss. Q1 By using the appropriate method, check and elaborate the stability of the pin-jointed plane truss (a) (b) Determine all reactions at the supports
Two links, made up of aluminum and steel, are connected by a hinge joint and an axial load P = 1000N is applied at node 3 as shown in Fig. 1.34. Determine the stresses developed in the two links using the finite element method. Link 1, Steel Link 2, Aluminum E=207 GPa; A=4cm2 E=71 GPa; A=2cm? 3 40 cm 60 cm FIGURE 1.34 Two links subjected to an axial load.
An extruded polymer flexural member is subjected to an internal axial force of P = 580 lb,an internal shear force of V = 420 lb, and an internal bending moment of M = 6,400 lb·in., actingin the directions shown in Figure P12.5a. The cross-sectional dimensions (Figure P12.5b) of theextrusion are b1 = 2.0 in., t1 = 0.6 in., b 2 = 4.0 in., t2 = 0.4 in., d = 4.5 in., and tw = 0.4 in.Determine the normal and shear stresses acting on horizontal and vertical planes:(a) at point H, which is located at a distance of yH = 0.8 in. above the z centroidal axis.(b) at point K, which is located at a distance of yK = 1.1 in. below the z centroidal axis.Show the stresses on a stress element for each point