Falling Sphere Viscometer Given:             Inner diameter of cylindrical tube = 0.03 m             Diameter of sphere = 0.02 m             Mass of sphere = 0.025 kg             Mass of liquid = 0.08 kg             Height of liquid = 0.14 m             Distance travelled by the sphere in the liquid = 0.06 m             Time of travel by the sphere in the liquid = 95 s   Calculate: The viscosity of the liquid in Pa – s.   NOTE: Answer the situations with complete solutions. Write your final answer in two decimal places. Please input the correct unit. Thankyou

Q: A force F = 185 N is applied to a two-bar truss as shown and 0 = 36 degree. Determine the value of…

A: FBD of the question can be drawn as shown below:   From the data given in question, F = 185 N θ =…

Q: • Part C- Hooke's law and strain hardening When the bar in Part B is unloaded, it will have a…

A:

Q: strain scale of 1 in.=0.001 in./in. stress. Use a scale of 1 in. = 20 ksi and 1 in. = 0.05 in./in.…

A:

Q: Air at 1 MPa and 600°C enters a converging nozzle with a velocity of 150 m/s. Determine the mass…

A:

Q: The ball B has a mass of 14 kg and is attached to the end of a rod whose mass may be neglected as…

A:

Q: 21.313 kg per second of water at 0.03398675 kbarg and internal energy of 15000 kW is heated at…

A:

Q: Required information Consider the given state of stress. Take Y=4 ksi. 10 ksi Determine the normal…

A:

Q: Given data : K=70 MPa Poisson ratio30.22 Find E

A: Given data : Bulk modulus=K Poisson ratio=μ   Required : Modulus of elasticity

Q: Where can I apply solving matrices in thermodynamics?

A: Apply of matrices in thermodynamics

Q: L081-kg steam-water mixture at 1.0 MPa is contained in an inflexible tank. Heat is added until the…

A:

Q: The circular shaft shown is subjected to an axial force P at its free end and a compressive force of…

A: Answer: The maximum allowable value of load P is 11.66 kips.

Q: A flanged bolt coupling has ten (10) steel 25.4 mm diameter bolts evenly tighten around a 415 mm…

A: Given: n = 10 D = 25.4 mm R = 415/2 mm tau = 50 MN/m2

Q: IS effect on heat transfer?Explain this with the illustration that shows its effect on the thickness…

A: A groove is a long, narrow depression formed into a material for the purpose of allowing another…

Q: Find Stress Force=2 N Cross sectional area=1 m2

A: Given data : Force=F Cross sectional area=A   Required : Stress

Q: 1- Through the results of the experiment and graphs, what is the effect of the following factorson…

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: Water vapor at 100 kPa and 150°C is compressed isothermally until half the vapor has condensed. How…

A:

Q: 1. An engine operating on the air diesel cycle with k-1.3 has thermal efficiency of 63% and a…

A:

Q: A cantilever beam, 100 mm wide by 230 mm high and 7 m long, carries a load that varies uniformly…

A: Due to bending in a beam , there are two types of stresses acting in a beam which are- 1. Bending…

Q: 3. For a single cylinder petrol engine works on the diesel cycle, the pressure at the beginning and…

A:

Q: The power and energy of machining calculation is important for: Select one: a. documentation of the…

A: Ans: (b) is correct. Pricing

Q: The rigid beam is supported by three 25-mm diameter A-36 steel rods. If the beam supports the force…

A: Find the force in each member.

Q: A turbine has an available enthalpy of 3300 kJ/kg in a Rankine cycle. The pump work has also 23…

A: Given Enthalpy = 3300 kJ/kg Power work = 23 kJ/kg Mass flow rate = 5 kg/s To find The work done in…

Q: A piston-cylinder assembly contains a two-phase liquid-vapor mixture of water with an initial…

A: Answer: The work is 1375 kW.

Q: The percentage humidity of air at 25°C and a total pressure of 790 mmHg is 60%. Calculate the…

A:

Q: -6 in.-3 in.- Problem #3 6 in. Figure 3 Refer to Fig. 3 a) Determine the moment of Inertia, Ix, of…

A:

Q: N2 enters a steady-flow heat exchanger at 150 kPa, 10°C, and 100 m/s, and it receives heat in the…

A:

Q: 8.881 kg of steam at a pressure of 20 bar and temperature of 300 deg C expands isentropically to a…

A:

Q: The pump is mounted 2.0 m above the water level. There is a 50 mm PVC pipe connected to the suction…

A:

Q: A hydraulic motor with a volumetric displacement of 5 in'/rev is supplied with a fluid flow rate of…

A: Given:- Volumetric displacement,d=5in3rev,Flow Rate,Q=180 gpm,Fluid Pressure,P=2200 psi,Mechanical…

Q: A system consisting of 2 kg of water initially at 100°C, 10 bar undergoes an internally reversible,…

A:

Q: A pipeline, 50 cm diameter and 4,500 m long, connects two reservoirs whom constant difference of…

A:

Q: ou are abducted by aliens and find yourself locked in a large room on some strange planet. To pass…

A: Given that, Mass of the ball, mb=7 kg,Mass of the chain, mc=0.5 kg,Length of the chain, l=2 m,Time…

Q: Draw the free-body diagram for the portion of machine structure shown in Figure 1. Determine the…

A:

Q: Gear 2 Gear 3 Output N3 = 25 teeth Idler N2 = 75 teeth ng: Sear 1) pitch diameter (1 mark) pitch…

A:

Q: A piston-cylinder assembly contains a two-phase liquid-vapor mixture of water with an initial…

A: Given that: At initial condition, dryness fraction = 50%. Mass of piston = 15 kg, and diameter = 10…

Q: Problem 2 ots 1-D Heat Transfer with Convection. The solid material is subjected to a temperature…

A: Convection is the course of hotness move by the mass development of atoms inside liquids like gases…

Q: Fluid of specific gravity 0.83 flows in a 238 mm diameter pipe. Find the critical velocity in m/s.…

A:

Q: Draw the free-body diagram for the portion of machine structure shown in Figure 1. Determine the…

A:

Q: A) Use the Bending Moment diagram show below to construct the shear and load diagrams. 35 20 5 ft-…

A:

Q: When filled to capacity, the unpressurized storage tank shown contains water to a height of h- 21…

A:

Q: 7.261 kg of steam at a pressure of 20 bar and temperature of 300 deg C expands isentropically to a…

A:

Q: Indirect Cooling With Liquid Nitrogen. You are designing a system to cool an insulated silver plate…

A: given : T1 = 77.2K T2= 65 F = 291.4 K

Q: Two pieces of carbon fiber composite are glued together as a lap joint. Shear stress is t= P /A. If…

A:

Q: 11-4.18. The bent bar ABC weighing 10 lb/ft is mounted as shown in Fig. P-11-4.18. upon a carriage…

A: Given: The bar weight, w = 10 lb/ft The carriage weight, W = 240 lb The load, P = 108 lb

Q: 2, A diesel Cycle engine with k of 1.33 has an air standard efficiency of 60.5%. The temperature…

A:

Q: 3. For a single cylinder petrol engine works on the diesel cycle, the pressure at the beginning and…

A:

Q: Three 18-mm-diameter steel bolts are to be used to attach the steel plate shown to a wooden beam.…

A: Find the factor of safety . Find allowable shear stress and find factor of safety by dividing…

Q: A steel rod placed between two walls is an exact fit and is stress-free at 20 degrees Celsius. Find…

A: The temperature at which the compressive stress becomes 100 MPa is 62.7350 ℃.

Q: water vapor at 100kpa and 150 C is compressed isothermally until the half of the vapor has…

A:

Q: A system consisting of 2 kg of water initially at 100°C, 10 bar undergoes an internally reversible,…

A: Find the final pressure and work done by the system.

Properties of Fluids

The term fluid represents a type of substance that can easily change its shape under any external pressure/force and can flow. Fluids can acquire any shape in which it is stored and can resist normal stresses but cannot resist shear stress in rest condition. Whenever external shear stress is applied to fluids, it starts to flow. The fluids may be liquid or gas. Example- water, air, etc.