Example 5.15. An overhang crank with pin and shaft is shown in Fig. 5.18. A tangential load of 15 kN acts on the crank pin. Determine the maximum principal stress and the maximum shear stress at the centre of the crankshaft bearing. Crank pin- 15 kN W 140 mm Crank web Crank shaft -120 mm- Fig. 5.18 80 mm

Example 5.15. An overhang crank with pin and shaft is shown in Fig. 5.18. A tangential load of 15 kN acts on the crank pin. Determine the maximum principal stress and the maximum shear stress at the centre of the crankshaft bearing. Crank pin- 15 kN W 140 mm Crank web Crank shaft -120 mm- Fig. 5.18 80 mm

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.2.4P: Repeat Problem 11.2-3 assuming that R= 10 kN · m/rad and L = 2 m.

See similar textbooks

Similar questions

Problem 1: If the parts of the shaft below are a 1" diameter solid steel rod and a 2" OD diameter steel pipe with a 0.25" wall thickness, what is the torsional stress in each section of the shaft? B 6 in. 15 lb 8 in. 15 lb
Torsion. A flanged bolt coupling connects two shafts. The bolt circle diameter is 250 mm in which there are 12 bolts. The allowable shear stress is 55 MPa in the shafts and 23 MPa in the bolts. One shaft is hollow with outside diameter of 100 mm, while the other one is solid of diameter 50 mm. Determine the ratio of the outside and inside diameter of the hollow shaft and the bolt diameter so that both shafts and the flanged bolt coupling are having the same strength in torsion.
Two 35 mm shafts are connected by a flanged coupling. The flanges are fitted with 6 bolts on 125 mm bolt circle. The shafts transmit a torque of 800 N-m at 350 rpm. For the safe stresses mentioned below, Safe shear stress for shaft material = 63 MPa Safe stress for bolt material = 56 MPa Safe stress for cast iron coupling = 10 MPa %3D Safe stress for key material = 46 MPa Calculate: (i) diameter of bolts ; (ii)thickness of flanges ; (iii)key dimensions ; (iv)hub length; and (V)power transmitted.
A sleeve made of AISI 1040 CD steel has inner and outer diameters 40mm and 50mm, respectively. It is press fit on a solid shaft of same material with diameter 42mm such that the nominal diameter between sleeve and shaft became 41mm. a. Find the pressure developed between shaft and sleeve. b. Draw the tangential, radial, and total stress as a function of radius, for both sleeve and shaft. c. Find the maximum shaft diameter that can be used before failure.
3. Determine the maximum average shear stress developed in each -in diameter bolt for the system shown below. 10 kip 5 kip 5 kip
Problem 1. A shaft with a diameter d = 60 mm must transfer a torque of 350 Nm by using a key joint. The key has the following standard dimensions: b x h x 1= 18 mm X 11 mm x 50 mm. Calculate the stresses.
2.A lever secured to a 2 inches round shaft by a steel tapered pin (d = 3/8”) has a pull of 50 lbs at a 30 inch radius from shaft center. Find the unit working stress of the pin.
Bearing stress 4. Please provide proper discussion and illustration also complete solution and clear solution please thank you Determine the length of a square key to be used for a 3.73 kW, 1800 rpm electric motor if the motor shaft diameter is 35 mm and the width of the key is approximately one-fourth of the shaft diameter. The allowable shearing stress on the key is 2.45 MPa
Q1 The screw of the shaft straightener exerts a load of 3000Kg. The screw-type is square threaded of outside diameter (7.5cm) and (6mm) pitch. Take the height of the nut (150mm). Determine 1) Force required at the rim of 30cm diameter hand wheel, assuming a coefficient of friction is 0.12. 2) The maximum compressive stress in the screw, bearing pressure on the thread, and shearing stress in the thread. 3) Efficiency of the straightener. Nut T 150 ↓ Hand wheel Screw 100 150- 400 All dimensions in mm
In a machine shop, the band saw blade is cutting through a work piece that is fed between the two guide blocks B. To what tension P should the blade be set if its stress is to be 3 ksi during use? Neglect the small size of the teeth relative to the blade's width. 3 in. 0.025 in. in. (Express your answer using three significant figures.) P=| lb
QUA four stroke internal combustion engine has the following specifications: Brake power 7.5 kW; Speed 1000 r.p.m.; Indicated mean effective pressure 0.35 N/mm2; Maximum gas pressure 3.5 N/mm2; Mechanical efficiency - 80 %. Determine: 1. The dimesions of the cylinder, if the length of stroke is 1.4 times the bore of the cylinder: 2. Wall thickness of the cylinder, if the hoop stress is 35 MPa: 3. Thickness of the cylinder head and the size of studs when the permissible stresses for the cylinder head and stud materials are 45 MPa and 65 MPa respectively. Any other data required for the design may be assumed.
TASK A hydraulic cylinder with a bore radius of 100 mm and an outer radius of 200 mm has been designed to withstand a maximum internal pressure of 200 MPa in service. During operation, the pressure within the cylinder is retained by a freely sliding piston. The steel used in the manufacture has Young's modulus of 210 GNm-2 Note: There is no axial stress generated in the cylinder wall in this application. 1. Elastic Stress Distributions in a Single Cylinder a) At an operating pressure of 200 MPa, calculate using Lame's equations the radial and circumferential stresses at the cylinder bore and the outer surface. Graphically present (sketch) the general form of variation of each of these stresses across the cylinder wall, clearly indicating the calculated values at the cylinder bore and at the outer surface. b) For the same operating pressure, calculate the maximum shear stress values at the cylinder bore and the outer surface. Hint: For axisymmetric problems, there are no shear stresses…