Example 33:A thyristor used in a half wave rectifier used 220V, with firing angle 60°, totalresistance load 10 , inductance 5mH and frequency 60Hz , calculate:(a) load voltage and current (b) maximum direct voltage and current (c) normalizedvoltage and current (d) root mean square voltage and current and (f) power factor.

Answered: Image /qna-images/answer/4e477dc4-d600-4e41-80e4-f83a5b8f12d8.jpg

Example 33: A thyristor used in a half wave rectifier used 220V, with firing angle 60° , total resistance load 12 , inductance 5mH and frequency 60HZ , caleulate: (a) load voltage and current (b) maximum direct voltage and current (c) normalized voltage and current (d) root mean square voltage and current and (f) power factor.

Example 33: A thyristor used in a half wave rectifier used 220V, with firing angle 60° , total resistance load 12 , inductance 5mH and frequency 60HZ , caleulate: (a) load voltage and current (b) maximum direct voltage and current (c) normalized voltage and current (d) root mean square voltage and current and (f) power factor.

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

What is CEMF?
What is the difference between a diode and rectifier?
How is a solid-state diode tested? Explain.
Example 35: A full wave rectifier used 220v , with firing angle 10° ,total resistance load5 K2, inductance 2.34 H,and frequency 60HZ , Draw and calculate: (a) VD.c and ID.c (b) VD.C(Max) (c) Vn (d) Vor.m.s.
A single phase – half wave controlled rectifier with freewheeling diode is supplying a load consistingseries connected a resistor and an inductance from a 70.7V (RMS), 50Hz sinusoidal AC source.The firing delay of the thyristor is 90° and the load values are R=10Ω, L=0.1 H. Define the loadcurrent expression and draw the load current by calculating for first two periods. And calculate theaverage values of the load voltage and current.
Design a single-phase full wave bridge rectifier with input voltage of 100v and inductive load of 10ohm and 40mH a. Show the waveform relation between the I/P and O/P b. Calculate the average O/P voltage c. Calculate the rms current
A single-phase half wave uncontrolled rectifier circuit is operating with a purely inductive load and a source voltage of 100 sin (277t) V. An ideal PMMC ammeter is connected in series with the inductive load reads 20 A. Calculate the distortion factor of the rectifier. Answer Choices: a. 0.866 b. 0.707 c. 0.577 d. 0.816
iii. For fully controlled single phase bridge rectifier with inductive load (load current is continuous) ,supply voltage 220 V(RMS) and a=30° .The mean value of output voltage is : (a) 150.32V (b) 171.52V (c) 120.98V
A R-load half-wave rectifier used sinusoidal voltage source with a peak value (35.353kV). The firing angle is (30). The total resistance is 50k2 and frequency is 50HZ. Calculate (in details): load direct voltage, maximum direct voltage, normalized voltage and effective voltage, power delivered to the load, power factor, form factor, ripple factor?
A three phase fullwave controlled rectifier has an input voltage which is 480vrmsat 60hz. the load modelled as a series resistance and inductance with R=10ohm and l=50mH. determine the delay angle to produce an average of 50ain the load.
A full wave bridge rectifier is supplied from 230V, 50Hz and uses a transformer of turns ration 15:1. It uses load resistance of 50 ohms. Calculate load voltage and ripple voltage. Assume ideal diode and transformer. Assume ripple factor equals to 0.482. a.Load Voltage= 13.8 V; Ripple Voltage=6.652 V b.Load Voltage= 15.6 V; Ripple Voltage=7.611 V c.Load Voltage= 21.3 V; Ripple Voltage=8.410 V d.Load Voltage= 25.1 V; Ripple Voltage=10.442 V
A three phase full wave rectifier is shown below along with peak phase voltage Vm-169.7V. The load is purely resistive. The rectifier delivers Ipc = 100 A and the source frequency is 60 Hz. The DC output voltage is %3D VDc=280.7V and the output RMS voltage is equal to VRMS=280.93V. The efficiency, FF and RF are respectively equal to: Secondary D D D, R AD. Z D. D, Select one: O a. 99.83%, 100.08%, 4% O b. 99.83%, 55.08%, 4% O C. 99.83%, 100.08%, 16% O d. 87.83%, 100.08%, 4%