Example (2-3):A centrifugal pump is installed to supply water from areservoir to a tank which is at a vertical height of 12 m above it. The diameter of the suction pipe is 300 mm and it is 6 m long. At the end of the suction pipe which extends under the water level in the reservoir, are fitted a foot valves and strainer. There is one 90° bend on the side of suction. The discharge pipe is 250 mm diameter and 135 m long. It is fitted with a gate valve and two medium radius 90°- elbows. Find the HP of the pump to discharge 85 L/s of water considering all losses of head in pipe fitting. The overall efficiency of pump is 70%. Find also the size of driving motor. Assume; Kinematic viscosity of water v = 1.146 * 10-6 m²/s %3D Loss of head due to friction in pipes Hf 4fL v2 d 2g 0.21 /here; 4f = 0.0032 + R0.237

Example (2-3):A centrifugal pump is installed to supply water from areservoir to a tank which is at a vertical height of 12 m above it. The diameter of the suction pipe is 300 mm and it is 6 m long. At the end of the suction pipe which extends under the water level in the reservoir, are fitted a foot valves and strainer. There is one 90° bend on the side of suction. The discharge pipe is 250 mm diameter and 135 m long. It is fitted with a gate valve and two medium radius 90°- elbows. Find the HP of the pump to discharge 85 L/s of water considering all losses of head in pipe fitting. The overall efficiency of pump is 70%. Find also the size of driving motor. Assume; Kinematic viscosity of water v = 1.146 * 10-6 m²/s %3D Loss of head due to friction in pipes Hf 4fL v2 d 2g 0.21 /here; 4f = 0.0032 + R0.237

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Given this vacuum pump Rated Voltage: DC4.5-6.6V No-load Current: 0.15A Pressure Range: 400-650 mm Hg and a single round 25mm diamter suction cup. Can you show the solution in the pressure exerted of the pump?
Problem # 3: Friction losses and volumetric discharge through a water piping system The cold-water faucet in a house is fed from a main water line through the following simplified piping system: A. A 160 ft long ¾ in ID copper pipe leading from the main line to the faucet base B. Six 90° standard elbows C. One wide-open angle valve with no obstruction D. The faucet which is considered to be composed of twd parts: 1) a half-open globe valve and 2) a nozzle having a diameter of 0.10 in. The pressure in the main line is 60 psig (virtually independent of flow) and the velocity there is negligible. At the faucet, the pressure is atmospheric. Assume the density of water to be 62.4 lbm/ft and the kinematic viscosity of water is 1.22 ×10³ ft²/s. Find the maximum volumetric flow rate of discharge from the faucet. This is trial and error problem. For a first trial, assume the Fanning friction factor to be 0.007. Use 5×106 ft for copper roughness. Neglect changes in elevation throughout the…
Item#3 The oil tank for the hydraulic system of figure below is air-pressurized at 10psig. The inlet line to the pump is 10 ft below the oil level while point 3 is 2ft below pump inlet. The pump flow-rate is 30 gpm and has a power equal to0.5HP. Find the pressure at station 3if there is a 28ft head loss between station 1 and 3. OIL LEVEL SG 0.9 1.5-IN- INSIDE DIAMETER 10 FT STRAINER ELECTRIC MOTOR M 2 FT PUMP 3 Q-30 GPM
10.0 m 200 m 2. An old western town has a water tower to deliver water to the residents. Pictured above is the water tower. The water tower is closed but there is a section of air that is atmospheric pressure just above the water. The corsss ectional area at point 2 is 4.75 x 10 m. The cross sectional area fot the water tower is very large. What is the speed of the water coming out of the pipe at point 2? (density of water = kg/m³) 3. On a vacation trip up in Oregon my boys decided to build a 10 kg raft that they made out of driftwood. 1000
4. FLUID FLOW 1. The figure below shows a water tank with piping system for a small manufacturing plant. If water flows through the system ((A) at 40 L/s, what would be the pressure at point B? The water has a density of 998 kg per cubic meter and viscosity of 0.8 centipoise. measures 0.04089 m and 0.04826 m in inside and outside diameter, respectively. The tank is exposed to the atmosphere The 1.5 inches (nominal) wrought iron pipe Given: Q= 40L/s = 0.040 m/s p= 998 kg/m H=0.8 centipoise 0.001P-s = 0.08 P-S Reg'd: Pressure at B. = ? 1 cp i.d. = 0.04089 m o.d. = 0.04826 m length of pipe = 110 m
Example 4: If the diameter at section 1 is D₁ = 0.5 m, and at section 2 the diameter D₂ = 0.2 m. All the other conditions are the same as in Exercise #3. What power in kilowatts and in horsepower must be supplied to the flow by the pump? Assume h₁ = 3 m of water and a₁ = α₂ = 1. Water is being pumped through a system. D₁ = 0.5 m Z₁ = 30 m P₁ = 70 kPa gage α₁ = 1.0 1 Pump Sual Z₂ = 40 m P2 = 350 kPa gage %₂ = 1.0 D₂ = 0.2 m Head loss in pipe = 3 m Water Q = 0.5 m³/s Properties: Water (10°C, 1 atm, Table A.5): y = 9810 N/m³
For a pumper truck pumping water to a fire, the back pressure is the additional pressure on the pump caused by the height of the nozzle. (Another way of thinking of back pressure is as the minimum pressure the pumper must produce in order to make water flow out the end of the nozzle.) Consider a pumper at street level pumping water through a hose to firefighters on the top of the ninth floor of a building. If each floor is 16 feet high, what is the head of water at the mouth of the nozzle?
4. A centrifugal pump delivers water to a height of 22 metres at a speed of 800 r.p.m. The velocity of flow is constant at a speed of 2-0 m/s and the outlet vane anglc is 45°. If the pump discharges 225 litres of water per second, find the diameter of the impeller and width of the impcller at oudet. (Ans. 375 mm: 95 mm)
Consider a hydraulic jack being used in a car repair shop, as in Fig. The pistons have an area of A1 = 0.8 cm2 and A2 = 0.04 m2. Hydraulic oil with a specific gravity of 0.870 is pumped in as the small piston on the left side is pushed up and down, slowly raising the larger piston on the right side. A car that weighs 13,000 N is to be jacked up. (a) At the beginning, when both pistons are at the same elevation (h = 0), calculate the force F1 in newtons required to hold the weight of the car. (b) Repeat the calculation after the car has been lifted two meters (h = 2 m). Compare and discuss
High of water in pump suction side is 8 m, neglecting of all losses, how much is the pump suction pressure? (105 N/m2 = 1 bar)
A "spa tub" is to be designed to replace bath tubs in reno- vations. There are to be 6 outlet nozzles, each with a di- ameter of 12 mm, and each should have an outlet velocity of 12 m/s. What is the required flow rate from the single pump that supplies all of these nozzles? If there is one suction line leading to the pump, what is the minimum diameter to limit the velocity at the inlet of the pump to 2.5 m/s?
Exercise Problem No. 2: The water flow of 35,000 Liters/min was developed into a booster station with a pump installed rated as follows: Pressure at Discharge side= 4.18 bars, 850mm above the pump C.L. Suction Pressure= 220mmHg vacuum, 425mm below the pump C.L. Pipe Dia @ suction=16 inches and Pipe Dia @ Discharge 12 ½ inches. 1. Draw the illustrative diagram 2. Calculate the Head at discharge, Velocity Head, Elevation Head and the Total Head of the Pump.