Example 4:If the diameter at section 1 is D₁ = 0.5 m, andat section 2 the diameter D₂ = 0.2 m.All the other conditions are the same as inExercise #3.What power in kilowatts and in horsepowermust be supplied to the flow by the pump?Assume h₁ = 3 m of water and a₁ = α₂ = 1.Water is being pumped through a system.D₁ = 0.5 mZ₁ = 30 mP₁ = 70 kPa gageα₁ = 1.01PumpSualZ₂ = 40 mP2 = 350 kPa gage%₂ = 1.0D₂ = 0.2 mHead loss in pipe = 3 mWaterQ = 0.5 m³/sProperties: Water (10°C, 1 atm, Table A.5): y = 9810 N/m³

Answered: Image /qna-images/answer/15062ed1-03e6-470c-b834-28ebb97fbaf7.jpg

If the diameter at section 1 is D₁ = 0.5 m, and at section 2 the diameter D₂ = 0.2 m. All the other conditions are the same as in Exercise #3. What power in kilowatts and in horsepower must be supplied to the flow by the pump? Assume h = 3 m of water and a₁ = α₂ = 1. Water is being pumped through a system. D₁ = 0.5 m Z₁ = 30 m P₁ = 70 kPa gage a₁ = 1.0 1 I Pump Z₂ = 40 m P2= 350 kPa gage a₂=1.0 D₂ = 0.2 m Head loss in pipe = 3 m Water Q=0.5 m³/s Properties: Water (10°C, 1 atm, Table A.5): y = 9810 N/m³

If the diameter at section 1 is D₁ = 0.5 m, and at section 2 the diameter D₂ = 0.2 m. All the other conditions are the same as in Exercise #3. What power in kilowatts and in horsepower must be supplied to the flow by the pump? Assume h = 3 m of water and a₁ = α₂ = 1. Water is being pumped through a system. D₁ = 0.5 m Z₁ = 30 m P₁ = 70 kPa gage a₁ = 1.0 1 I Pump Z₂ = 40 m P2= 350 kPa gage a₂=1.0 D₂ = 0.2 m Head loss in pipe = 3 m Water Q=0.5 m³/s Properties: Water (10°C, 1 atm, Table A.5): y = 9810 N/m³

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1. A pump (Figure 4-07) takes water from a 200-mm suction pipe and delivers it to a 150-mm discharge pipe in which the velocity is 2.5 m/s. At A in the suction pipe, the pressure is -40 kPa. At B in the discharge pipe, which is 2.5 m above A, the pressure is 410 kPa. What horsepower would have to be applied by the pump if there were no frictional losses? 2. A pump (Figure 4-07) takes water from a 200-mm suction pipe and delivers it to a 150-mm discharge pipe in which the velocity is 3.6 m/s. The pressure is -35 kPa at A in the suction pipe. The 150 mm pipe discharges horizontally into air at C. To what height h above B can the water be raised if B is 1.8 m above A and 20 hp is delivered to the pump? Assume that the pump operates at 70 percent efficiency and that the frictional loss in the pipe between A and C is 3 m.
1. A pump (Figure 4-07) takes water from a 200-mm suction pipe and delivers it to a 150-mm discharge pipe in which the velocity is 2.5 m/s. At A in the suction pipe, the pressure is -40 kPa. At B in the discharge pipe, which is 2.5 m above A, the pressure is 410 kPa. What horsepower would have to be applied by the pump if there were no frictional losses?
2.14. A pump is driven by a two-speed motor having speeds of 1750 and 1185 rpm. At 1750 rpm, the flow is 45 gpm, the head is 90 ft, and the total efficiency is 0.60. The pump impeller has a diameter of 10 in. a. What values of Q, H, and ns are obtained if the pump runs at 1185 rpm? b. Find the specific speed and the specific diameter of the pump (at 1750 rpm).
Item#3 The oil tank for the hydraulic system of figure below is air-pressurized at 10psig. The inlet line to the pump is 10 ft below the oil level while point 3 is 2ft below pump inlet. The pump flow-rate is 30 gpm and has a power equal to0.5HP. Find the pressure at station 3if there is a 28ft head loss between station 1 and 3. OIL LEVEL SG 0.9 1.5-IN- INSIDE DIAMETER 10 FT STRAINER ELECTRIC MOTOR M 2 FT PUMP 3 Q-30 GPM
A farmer has a pump which discharges 100 lpm of water at a head of 10 m. The pump is driven by anelectric motor at speed of 1700 rpm through 4”x 4” pulley-drive combination for the motor and thepump, respectively, what would be the pump output if the motor pulley is changed to six inchesdiameter?
Seven hundred gpm of water are being discharged by a centrifugal pump 5 ft. above the pump inlet. The inlet pressure is 4-in Hg above atmospheric and the discharge pressure is 29 psia. Assume the pump input is 8 hp, if the pump has an 8-inch diameter inlet and a 4-inch diameter discharge: 1.How much pressure loss in the pump? a. 28.4 ft-lbf/lb b. 5 ft-lbf/lb c. 4.7 ft-lbf/lb d. 38.1 ft-lbf/lb 2. How much is the velocity loss in the pump? a. 28.4 ft-lbf/lb b. 45.3 ft-lbf/lb c. 4.7 ft-lbf/lb d. 38.1 ft-lbf/lb 3. If the pump speed is increased from 1600 to 2400 rpm, what will be the new net flow rate in the pump? a. 800 gpm b. 1050 gpm c. 1400 gpm d. 1965 gpm 4. Find the new brake horse power if the pump speed in increased from 1600 to 2400 rpm. a. 64 hp b. 20.25 hp c. 8 hp d. 30.375 hp
4. A centrifugal pump delivers water to a height of 22 metres at a speed of 800 r.p.m. The velocity of flow is constant at a speed of 2-0 m/s and the outlet vane anglc is 45°. If the pump discharges 225 litres of water per second, find the diameter of the impeller and width of the impcller at oudet. (Ans. 375 mm: 95 mm)
4. In figure below find the force F, required to stop the system from moving if p/-10 psi, p2=0, V₁=10ft/s and the flow rate is increasing by 3000 gpm/min. 4 in. diam T -10 ft- -20 ft 8 in. diam
Include a free body diagram. pump draws water from a sump through a vertical 6′′ pipe. The pump has a horizontal discharge pipe 4′′ in diameter that is 10.6 ft above the water level in the sump. While pumping 1.25 cfs, gages near the pump at entrance and discharge read —4.6 psi and +25.6 psi, respectively. The discharge gage is 3.0 ft above the suction gage. Compute the horsepower output of the pump and the head lost in the 6′′ suction pipe. (ANSWER: 10.7 Hp, 2.4 ft)
10.0 m 200 m 2. An old western town has a water tower to deliver water to the residents. Pictured above is the water tower. The water tower is closed but there is a section of air that is atmospheric pressure just above the water. The corsss ectional area at point 2 is 4.75 x 10 m. The cross sectional area fot the water tower is very large. What is the speed of the water coming out of the pipe at point 2? (density of water = kg/m³) 3. On a vacation trip up in Oregon my boys decided to build a 10 kg raft that they made out of driftwood. 1000
6.1 D, and D, are the inlet and outlet diameters of the pipe connected to the water turbine shown in the figure. The gage pressure at the inlet and outlet of the turbine are p, and p2. The elevation difference between the pipe inlet and outlet is h. If the water flow rate is Q and the total frictional losses is H1. Determine the mechanical power delivered by the turbine if it is 90% efficient. D; Turbine, D2 Dj = 320 mm D2 = 160 mmn h= 45m P1 =10.5bar P2 =5.5 bar Q = 0.065 m³.sl HL =8.0 m
Water at 5°C is to be pumped from the river to the bottom of a water tower. The pump is 5 m above the river (dimension "a" on the diagram below) and is supplied by a 6.00 inch schedule 40 pipe. The tank is 19.5 m above the pump (dimension "b" on the diagram below) and is supplied by a 4 inch schedule 40 pipe. The water level in the tank is 4.3 m above the inlet (dimension "c" on the diagram below). The pump delivers 0.021 m/s. Losses are estimated to be 1.2 m between the river and the pump, and 4.2 m between the pump and the tank. Discharge line Suction line Pump River a) Calculate the losses in the suction line in kPa, based on the given head loss in m. kPa b) Calculate velocity in the suction line in m/s. m/s c) What is the pressure at the inlet to the pump in kPa? kPa