Water at 60 °F flows through a 6-in. schedule 40 pipe (D=6.065 in.), through a reducer, and then through a 4-in. schedule 40 pipe ( Dro = 4.026 in) at a rate of 80 gal/min. The pressure is 40 psig at the reducer inlet and 34 psig at the reducer outlet. Determine the force of the water on the reducer. Note: A reference other than this textbook will readily provide the actual inside diameter of the schedule 40 pipes you will need to answer this question.

Water at 60 °F flows through a 6-in. schedule 40 pipe (D=6.065 in.), through a reducer, and then through a 4-in. schedule 40 pipe ( Dro = 4.026 in) at a rate of 80 gal/min. The pressure is 40 psig at the reducer inlet and 34 psig at the reducer outlet. Determine the force of the water on the reducer. Note: A reference other than this textbook will readily provide the actual inside diameter of the schedule 40 pipes you will need to answer this question.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Need detailed solution. 4 decimal places. Oil with a specific gravity of 0.82 is flowing in a pipe under the condition below. If the total head loss from point 1 to point 2 is 3 ft, find the pressure at point 2 in psi. *cfs = cubic ft per sec
Handwriting not allow please
For Questions 3 to 5, consider the following conditions: a centrifugal pump has diameters d1 = 7 in, d2 = 13 in, blade widths b1 = 4 in, b2 = 3 in, blade angles B1 = 25° and B2 = 40°, and rotates at 1160 r/min. If the fluid is gasoline at 20°C (p = 1.319 slugs/ft^3) and the flow enters the blades radially, estimate the theoretical or "design" quantities.
5. A nozzle meter is to be designed to fit into an 18-in. galvanized pipe. Air at room temperature flows through the pipe at velocities varying from 700 to 1400 ft per min. If a 2-in. inclined manometer containing alcohol with a S.G. of 0.89 is to be used with the nozzle, what should be the diameter of the nozzle?
On average, you inhale approximately 1 L of air every 2 seconds. The pressure difference between the outside air and your chest cavity creates this flow. The air flows through your trachea which has a radius of 0.005m and a length of 0.12m. Do not ignore the viscosity of air in this problem. a. What is the velocity of the air moving through the trachea? b. Is this flow laminar or turbulent? Support your answer with calculations. c. What is the pressure in your chest cavity required to create this flow? Assume the outside air has a pressure of 1 atm.
The pressure through a section of pipe is 23 PSI and the velocity of the fluid is 3 ft/sec. If the velocity was increased to 5 ft/sec, what would the pressure drop be?
A manufacturing company uses a 100 bar hydraulic power system which supplies 10 liter/minute of oilflow. The shaft speed is 1500 RPM and the nominal displacement is 8 cm3/revolution. The theoreticaldrive torque is 11.4 Nm. If the electric motor driving the pump has an efficiency of 95%,a. Name in detail all 27 hydraulic power components as illustrated in the above figure.b. Calculate the volumetric efficiency, the fluid and shaft power, the overall efficiency of the pump.
Please fast only final answer needed
For Questions 3 to 5 A certain centrifugal pump was tested and its performance curves can be approximated as follows: H = 340 - 1.2(Q^2), in feet BP = (0.0521Q^3) + (1.250^2)+(11.042Q) + 134.5, in horsepower where Q is in ft^3/s. Question 3 If a single pump is used to deliver water of a system which requires a total of 8 ft^3/s, what is the efficiency of the pump (in %)? Take the specific weight of water to be 62.4 lbf/ft^3. Round your answer to 2 decimal places.
For the single pump-pipe system below, what will be the changes for the operating point if we increase the pipe size but decrease the shaft speed of the pump? EB H₂ O The operating point will remain the same. O The operating point will occur either at a higher discharge or at a lower discharge, depending on the specific influence of each change. O The operating point will occur at a higher discharge. O The operating point will occur at a lower discharge.
What is Total Head of submersible pump has Q=287 l/sec D=0.8 m Lenght of pipe=12000 m Fluid=water Fittings=6 elbows 45 degree Material=GRP Depth of well=9 meter Please take your time
Determine the power requirement of the pump shown in Figure 3.0, assuming it has an efficiency of 88%. The system has a loss coefficient of 3.0 up to point A, and K =1.2 from point B to point C. Neglect any losses through the exit nozzle. Additionally, compute the pressures at points A and B. Water 15 m 2 cm 4 cm dia. 5 cm dia. Figure 3.0 400 kPa