Example 133: A cylindrical steel pressure vessel 400 mm in diameter with a wall thickness of 20 mm, is subjected to an internal pressure of 4.5 MN/m². (a) Calculate the tangential and longitudinal stresses in the steel. (b) To what value may the internal pressure be increased if the stress in the steel is limited to 120 MN/m2.

Example 133: A cylindrical steel pressure vessel 400 mm in diameter with a wall thickness of 20 mm, is subjected to an internal pressure of 4.5 MN/m². (a) Calculate the tangential and longitudinal stresses in the steel. (b) To what value may the internal pressure be increased if the stress in the steel is limited to 120 MN/m2.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.7.15P: A brass plate with a modulus of elastici ty E = 16 X 106 psi and Poisson’s ratio a = 0.34 is loaded...

See similar textbooks

Similar questions

A cylindrical steel pressure vessel 60 cm in diameter with a wall thickness of 30 mun, is subjected to an internal pressure of 6 Nmm. (a) Calculate the tangential and longitudinal stresses in the steel. (b) To what value may the internal pressure be increased if the stress in the steel is limited to 200 MN/m?
A spherical pressure vessel 400 mm in diameter with a wall thickness of 15 mm. To what value may the internal pressure beincreased if the stress in steel is limited to 193 MPa?
Q3: A thin cylinder 75mm internal dimeter 250mm long has wall thick 2.5mm .It i found to change to internal dimeter is (33.4 x 10-6 m) determined the: 1-internal pressure applied on the thin cylinder. 2-if addition the internal pressure is transmitted 60 KW at 200 r.p.m find the principa stress set up in cylinder.(E-200 GPa and y = 0.3).
Example: A cylinder has an internal diameter of 230 mm, has walls 5 mm thick and is 1 m long. It is found to change in internal volume by 12.0 x m' when filled with a liquid at a pressure p. If E = 200GN/m2 and y= p.25, and assuming rigid end plates, determine: (a) the values of hoop and longitudinal stresses; (c) the necessary change in pressure p to produce a further increase in internal volume of (longitudinal) are assumed; 15 %. The liquid may be assumed incompressible.
A steel cylindrical pressure vessel with closed ends is 25 cm external diameter and 5 mm thick It is wound closely with a single layer of circular wire of diameter 1.2 mm. Under the tension of 96 N/mm'. If the cylinder is treated as thin. Calculate (1) Initial stress in cylinder. (ii) Initizl pressure which will produce a stress of 48 N/mm2.
A composite square member of varying sizes is subjected to axial forces along its centerline, as shown. The members' cross-sectional dimensions, from smaller to larger, are 50 mm ´ 50 mm, 75 mm ´ 75 mm, and 100 mm ´ 100 mm, respectively. (a) What are the normal stresses (in MPa) induced in the bar material at Section A-A, Section B-B, Section C-C? (b) What are the changes in the axial (4.28 ft), width (100mm), and thickness (100 mm) direction (in mm), at Section C-C? Assume n = 0.25 and E = 200,000 MPa., 1 ft = 0.3048 m
A cylindrical steel pressure vessel 400 mm in diameter with a wallthickness of 20 mm, is subjected to an internal pressure of 7.875 MPa.Calculate the tangential stress in the steel.
Problem 2: (M2) Design engineers in many situations must justify their selection of material. Your role in a mechanical design company that manufactures steel pipes is to confirm the maximum stresses imposed by a 250 psi oil pressure on the pipe wall, which acts as a pressurized cylinder once the gate valve is closed. If the pipe diameter is 1 foot and its wall is 0.25 inches thick. Evaluate the longitudinal and hoop stresses at point A. Valve A oil in Figure.3: Steel oil pipe
A cylindrical steel pressure vessel 400 mm in diameter with a wallthickness of 20 mm, is subjected to an internal pressure of 7.875 MPa.Calculate the longitudinal stress in the steel.
Example vacuum pressure): A thick cylinder of inner radius 8cm and outer radius 12 cm is subjected to an external pressure of -0.09M Pa. Internal pressure is atmospheric. Determine (a) the radial and tangential stress distribution across the the thickness, (b) the axial component of stress, if the ends of the cylinder are fixed. Assume v=0.3 and (c) maximum shear stress
1. A thin-walled cylinder with a diameter of 20 cm and a wall thickness of 2 mm is filled with gas at a pressure of 2 MPa. Calculate the longitudinal stress, and circumferential stress in the cylinder wall.
Q3: A cylindrical shell of 1.3 m diameter is made up of 18 mm thick plates. Find the circumferential and longitudinal stress in the plates, if the boiler is subjected to an internal pressure of 2.4 MPa.